YOKOGAWA AQ6370C

7-58
IM AQ6370C-17EN
:CALCulate:PARameter[:CATegory]:FIL
Pk
Function Sets/queries parameters for the FILTER PEAK
analysis function.
Syntax
:CALCulate:PARameter[:CATegory]:FIL
Pk<wsp><item>,<paramater>,<data>
:CALCulate:PARameter[:CATegory]:FIL
Pk?<wsp><item>,<paramater>
<item> = Analytical item that sets parameter(s)
<parameter> = Parameter to be set
<data> = Data to be set
<item> <parameter> <data>
PLEVel SW OFF|ON|0|1
PWAVelength SW OFF|ON|0|1
MWAVelength SW OFF|ON|0|1
ALGO THResh|RMS
TH <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|1
MDIFf <NRf>[DB]
SWIDth SW OFF|ON|0|1
ALGO THResh|RMS
TH <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|1
MDIFf <NRf>[DB]
XTALk SW OFF|ON|0|1
ALGO THResh|PLEVel|
GRID
TH <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|1
MDIFf <NRf>[DB]
CSPace <NRf>[M]
SARea <NRf>[M]
RWIDth SW OFF|ON|0|1
TH <NRf>[DB]
MDIFf <NRf>[DB
Example
:CALCULATE:PARAMETER:FILPK
SWIDTH,ALGO,THRESH
:CALCULATE:PARAMETER:FILPK?
SWIDTH,ALGO -> THR
:CALCULATE:PARAMETER:FILPK XTALK,
CSPACE,0.5NM :CALCULATE:PARAMETER:
FILPK? XTALK,CSPACE ->
+5.00000000E-010
Explanation • If a non-existing parameter is used for a
combination, an execution error occurs
(a combination of SWIDth and CSPace, etc.).
• On the AQ6373, the following data parameter
cannot be set.
GRID
• This is a sequential command.
:CALCulate:PARameter[:CATegory]:FPLD
Function Sets/queries parameters for the FP-LD analysis
function.
Syntax
:CALCulate:PARameter[:CATegory]:FPL
D<wsp><item>,<paramater>,<data>
:CALCulate:PARameter[:CATegory]:FPL
D?<wsp><item>,<paramater>
<item> = Analytical item that sets parameter(s)
<parameter> = Parameter to be set
<data> = Setting data
<item> <parameter> <data>
SWIDth ALGO ENVelope|THResh|
RMS|PKRMs
TH <NRf>[DB]
TH2 <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|1
MDIFf <NRf>[DB]
MWAVelength ALGO ENVelope|THResh|
RMS|PKRMs
TH <NRf>[DB]
TH2 <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|1
MDIFf <NRf>[DB]
TPOWer OFFSet <NRf>[DB]
MNUMber ALGO ENVelope|THResh|
RMS|PKRMs
TH <NRf>[DB]
TH2 <NRf>[DB]
K <NRf>
MFIT OFF|ON|0|11
MDIFf <NRf>[DB]
Example
:CALCULATE:PARAMETER:FPLD
SWIDTH,ALGO,THRESH
:CALCULATE:PARAMETER:FPLD?
SWIDTH,ALGO -> THR
:CALCULATE:PARAMETER:FPLD TPOWER,
OFFSET,1.0DB :CALCULATE:PARAMETER:
FPLD? TPOWER,OFFSET ->
+1.00000000E+000
Explanation • If a non-existing parameter is used for a
combination, an execution error occurs.
(a combination of SWIDth and OFFSET, etc.)
• This is a sequential command.
7.6 Instrument-Specific Commands