4-8
IM DL350E-17EN
4.1 List of Commands
Command Function page
:CHANnel<x>:STRain:BALance?
Queries the ON/OFF state of target channels when executing balancing
collectively on all channels of a strain module.
4-67
:CHANnel<x1>:STRain:BALance:CHA
Nnel<x2>
Sets or queries the channels that balancing will be performed on for a strain
module.
4-67
:CHANnel<x>:STRain:BALance:EXEC
ute
Executes strain balancing collectively on all strain modules. 4-67
:CHANnel<x>:STRain:BWIDth
Sets or queries the filter of a strain module. 4-67
:CHANnel<x>:STRain:EXCitation
Sets or queries the bridge voltage of a strain module. 4-67
:CHANnel<x>:STRain:GFACtor
Sets or queries the gauge factor of a strain module. 4-67
:CHANnel<x>:STRain:INVert
Sets or queries whether the display is inverted (ON) or not (OFF) for a strain
module.
4-67
:CHANnel<x>:STRain:LSCale?
Queries all the linear scaling settings of a strain module. 4-67
:CHANnel<x>:STRain:LSCale:AVAL
ue
Sets or queries the scaling coefficient A that is used during linear scaling for
a strain module.
4-67
:CHANnel<x>:STRain:LSCale:BVAL
ue
Sets or queries the scaling coefficient B that is used during linear scaling for
a strain module.
4-68
:CHANnel<x>:STRain:LSCale:DISPl
aytype?
Queries all the linear-scaling result display-mode settings of a strain module. 4-68
:CHANnel<x>:STRain:LSCale:DISPl
aytype:DECimalnum
Sets or queries the decimal place that is used when the linear-scaling result
display mode is set to Float for a strain module.
4-68
:CHANnel<x>:STRain:LSCale:DISPl
aytype:MODE
Sets or queries the linear-scaling result display mode of a strain module. 4-68
:CHANnel<x>:STRain:LSCale:DISPl
aytype:SUBunit
Sets or queries the unit prefix that is used when the linear-scaling result
display mode is set to Float for a strain module.
4-68
:CHANnel<x>:STRain:LSCale:GETMe
asure
Executes the measurement of the linear scaling P1:X or P2:X value of a
strain module.
4-68
:CHANnel<x>:STRain:LSCale:MODE
Sets or queries the linear scaling mode of a strain module. 4-68
:CHANnel<x>:STRain:LSCale:{P1X|
P1Y|P2X|P2Y}
Sets or queries the linear scaling P1:X, P1:Y, P2:X, or P2:Y value of a strain
module.
4-69
:CHANnel<x>:STRain:LSCale:SHUNt
Executes shunt calibration. 4-69
:CHANnel<x>:STRain:LSCale:UNIT
Sets or queries the unit string for linear scaling of the strain module. 4-69
:CHANnel<x>:STRain:RANGe
Sets or queries the measurement range of a strain module. 4-69
:CHANnel<x>:STRain:SCALe
Sets or queries the upper and lower limits of the screen for a strain module. 4-69
:CHANnel<x>:STRain:UNIT
Sets or queries the unit of a strain module. 4-69
:CHANnel<x>:TEMPerature?
Queries all settings of a module that can measure temperature. 4-70
:CHANnel<x>:TEMPerature:BURNout
Sets or queries whether burnout will be detected when temperature
measurements are performed.
4-70
:CHANnel<x>:TEMPerature:BWIDth
Sets or queries the bandwidth limit that is used when temperature
measurements are performed.
4-70
:CHANnel<x>:TEMPerature:COUPli
ng
Sets or queries the input coupling setting of a module that can measure
temperature.
4-70
:CHANnel<x>:TEMPerature:DUPeri
od (Data update period)
Sets or queries the date update interval setting of a 16-CH temperature/
voltage input module.
4-70
:CHANnel<x>:TEMPerature:RJC
Sets or queries the RJC that is used when temperature measurements are
performed.
4-70
:CHANnel<x>:TEMPerature:SCALe
Sets or queries the upper and lower limits of the screen that are used when
temperature measurements are performed.
4-70
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:BURNout
Sets or queries whether burnout will be detected when temperature
measurements are performed on a 16-CH temperature/voltage input module.
4-71
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:COUPling
Sets or queries the input coupling setting of a 16-CH temperature/voltage
input module.
4-71
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:LABel
Sets or queries the channel label when temperature measurements are
performed on a 16-CH temperature/voltage input module.
4-71
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:RJC
Sets or queries the RJC when temperature measurements are performed on
a 16-CH temperature/voltage input module.
4-71
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:SCALe
Sets or queries the upper and lower limits on the screen when temperature
measurements are performed on a 16-CH temperature/voltage input module.
4-72
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:TYPE
Sets or queries the thermocouple type to use when temperature
measurements are performed on a 16-CH temperature/voltage input module.
4-72
:CHANnel<x1>:TEMPerature:SCHann
el<x2>:UNIT
Sets or queries the unit when temperature measurements are performed on
a 16-CH temperature/voltage input module.
4-72
:CHANnel<x>:TEMPerature:TYPE
Sets or queries the thermocouple type that is used when temperature
measurements are performed.
4-72
To Next Page
Loading...
