ZinWave UNITIVITY 5000

To Next Page

To Previous Page

UNItivity 5000 Understanding the Components

User Manual

RS232 Connector

Alarm Connector (9 way D-type)

Status LEDs

Handle and Mounting Bracket (both sides of device)

Main Page

Table of Contents3
Safety and Regulatory Information8
Safety Information8
RF Exposure8
Installation8
Signal and Input Power8
Fiber Considerations9
Optical Safety Precautions10
Software Installation10
Symbols11
Regulatory Information11
UL NRTL Listing12
Fcc12
Innovation, Science and Economic Development Canada Compliance Statement17
CE Information17
Rohs Information19
UKCA Information20
About this Manual21
Intended Audience21
Conventions21
Getting Help21
System Overview22
How Does It Work22
Key Features23
Network Topologies23
Single-Star Configuration23
Double Star Configuration24
Mixed Topology Configuration24
Support for MIMO Services25
Understanding Optional Components26
How the PSU Fits in26
How the Active POI Fits in27
Understanding the Components28
Hubs29
Configuration GUI29
Primary Hub30
Secondary Hub32
Service Module33
Optical Module34
Transport Module35
Remote Unit36
Antennas37
Fiber Patch Cords37
Hub and Module Leds38
Primary Hub Front Panel Leds38
Secondary Hub Status Leds38
Optical Link to Primary Hub38
Optical Links to 8X Remote Units39
Service, Optical and Transport Module Leds39
Power LED-Right40
Communications-Middle40
Status-Left40
Start-Up Sequence41
Service Module41
Optical Module41
Transport Module42
Remote Unit Leds43
Performing a Basic Installation44
Installing and Populating Hubs45
Installing the Hub45
Mounting Kit45
Standard 19" (48.26Cm) Rack Mounting46
Open Frame Rack Mounting46
Installing Blank Panels47
Installing Secondary Hub48
Installing Service Modules in Primary Hub50
Installing Optical Modules in Primary Hub51
Powering the Primary Hub51
Powering the Secondary Hub52
Installing Remote Units53
Mounting Remote Units53
Considerations before Mounting53
Powering Remote Units56
PSU DC Power56
DAS Installation Considerations57
Antenna Requirements57
Isolation57
Isolation Measurement Techniques57
Uplink/Downlink Balance58
Connecting Antennas to Remote Units58
Connecting the PSU or Secondary Hub Power Port to Remote Units59
Power Distribution Requirements59
Understanding Connectors & Cabling60
Uplink System Noise61
Introduction61
Optimising SNR and Noise Level61
Unitransport63
Performing Basic Configuration64
Understanding the Configuration GUI65
Supported Browsers65
Initial Standalone Access65
Accessing the GUI67
Understanding the Main Window69
Address Bar69
Login Bar69
Help Button69
Display Area70
Progress Indicator70
Changing User Passwords and Timeouts71
Initial System Setup73
Connection to das System73
Software Upgrade73
Full System Software Upgrade73
To Update RU and SH Firmware from an Installed Primary Hub Software75
Release75
System Setup75
Import Coverage Tool Setting75
Primary Hub Configuration75
Service Module Downlink AGC76
Transport Module AGC76
Rack-Mount Power Supply Unit Configuration77
Secondary Hub Configuration and Controls77
Remote Unit Configuration77
System Status79
System Status Topology Tree and Modules79
Unit and Module Details79
Event Log79
Hub Setup80
Restart Hub80
IP Settings80
SNMP Settings80
User Interface Settings81
Date & Time81
Security Settings81
Alarms Setup82
System Maintenance82
System Views83
System Snapshot83
Alarm Counts83
Link Quality84
RU DC Power84
RU Calculations84
RF System Check84
Additional System Setup86
System Uplink/Downlink Balance86
Calculated Input Level86
Changing or Swapping Equipment86
Hub87
Remote Unit87
Optical Module87
Factory Reset of a Primary Hub87
Unitransport System Setup89
Unitransport Functionality89
Configuration of Unitransport Hub90
Configuration of Downstream Primary Hub91
Remote Configuration of Unitransport Hub92
Understanding Alarms & Reporting94
Alarms94
Loss of Service94
Service Warning95
Hardware Warning97
Informational99
Alarms Setup100
Alarm Connections100
Snmp101
SNMP V3 Manager Configuration101
SNMP Trap Events102
SNMP Get Objects102
3000 SNMP Traps103
Additional 5000 SNMP Objects103
Performing Diagnostics and Testing105
Diagnosing Optical Links with an OTDR105
Diagnose an Optical Link105
LED Testing106
Modules106
Remote Unit LED Test107
Event Log108
Viewing and Saving the Event Log108
System Logging108
Downloading Event Log108
System Log108
Specifications109

ZinWave UNITIVITY 5000 - Page 31

Table of Contents