ABB 265GS - Page 85

To Next Page

To Previous Page

Appendix

IM/265Gx/Ax-EN-07 265Gx, 265Ax 85

Main Page

Table of Contents3
Safety6
General Information and Notes for the Reader6
Intended Use6
Technical Limit Values6
Improper Use7
Target Groups and Qualifications7
Warranty Provisions7
Plates and Symbols8
Safety-/ Warning Symbols, Note Symbols8
Name Plate9
Compliance with Pressure Equipment Directive (97/23/EC)11
Transport and Storage12
1.10 Safety Instructions for Electrical Installation12
1.11 Safety Information for Inspection and Maintenance12
1.12 Returning Devices13
1.13 Integrated Management System13
1.14 Disposal13
Information on WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment)13
1.14.2 Rohs Directive 2002/95/EC14
Use in Potentially Explosive Atmospheres15
Type-Examination Certificate/Declaration of Conformity15
Type of Protection "Intrinsic Safety Ex I15
Use in Areas with Combustible Dust16
Category 3 for Use in "Zone 216
Type of Protection "Flameproof Enclosure Ex D17
Type of Protection "Intrinsic Safety I", "Flameproof Enclosure D", "Protection by Enclosure Td", and "Non-Sparking Na18
Canadian Standards Association (CSA): "Explosion-Proof18
Aspects of "Ex Safety" and "IP Protection" for Australian Applications19
Design and Function21
Principle of Operation and Construction22
Mounting25
General25
IP Designation25
Pressure Transmitter26
Sealing and Screw Connections26
Moisture27
Impulse Line27
Electrical Connections28
Cable Connection28
Electrical Connection in the Cable Connection Area29
Electrical Connection with Plug31
Assembling and Connecting the Socket Connector32
Protective Conductor / Grounding33
Integrated Lightning Protection (Optional)33
Communication Setup34
Connecting Cable36
PROFIBUS PA Pressure Transmitter37
Commissioning38
Output Signal39
Write Protection39
Correcting the Lower Range Value / Zero Shift40
Turning the Housing in Relation to the Measuring Equipment41
Installing / Removing the Button Unit41
Installing / Removing the LCD Display42
Securing the Housing Cover with Ex D44
Sensor Ventilation45
Operation46
Operation Using the Control Buttons on the Transmitter46
Configuration47
Factory Settings47
Transmitter with HART Communication and 447
Transmitter with PROFIBUS PA Communication48
Transmitter with FOUNDATION Fieldbus Communication49
Configuration Types49
Configuring the Parameters Without an LCD Display50
Configuration with the LCD Display52
Offset Shift (OFFSET SHIFT)53
Damping (DAMPING)54
Characteristic (FUNCTION)54
Fieldbus Address (ADDRESS)54
Layout and Contents of the LCD Display55
Displaying a Physical Value55
Menu Structure57
Menu-Controlled Pressure Transmitter Programming59
Parameter Description60
Configuration with the PC / Laptop or Handheld Terminal62
Configuration with the Graphical User Interface (DTM)64
System Requirements64
Setting the Damping Value65
Correcting the Zero Shift65
Setting the Lower and Upper Range Limit Values65
Ex Relevant Specifications66
Potentially Explosive Atmospheres66
Specifications70
Functional Specifications70
Operating Limits71
Pressure Limits71
Environmental Limits72
Electrical Data and Options72
Measuring Accuracy74
Operating Influences74
Technical Specification75
Mounting Dimensions (Not Design Data)76
Pressure Transmitter with Barrel Housing76
Pressure Transmitter with DIN Housing77
Pressure Transmitter with Front-Bonded Diaphragm (Barrel Housing)78
Pressure Transmitter with Ball Valve Connection (Barrel Housing)79
Mounting with Bracket for Barrel Housing (Option)80
Mounting with Bracket for DIN Housing (Option)81
Maintenance / Repair82
10.1 Removal83
10.1.1 Removing the Electronics83
10.1.2 Screw Torques for the Process Connection83
Appendix84
11.1 Approvals and Certifications84
Index87

ABB 265GS - Page 85

Table of Contents

Related product manuals