Appendix A – ACS/ACC/ACP 601 Technical Data
A-6 ACx=ACS/ACC/ACP ACS/ACC/ACP 601 Drives
Note:
Fuses from other manufacturers can be used if they meet the ratings given in the table. Only
ultra rapid fuses guarantee the proper protection for the rectifier semiconductors. The fuses
recommended in the table are UL recognized.
Example
For ACS 601-0120-3, the recommended fuses for the input bridge protection are 400 A
ultrarapid fuses.
The values
I
1N
and
I
1hd
for ACS 601-0120-3 are 175 A and 145 A respectively. 1.1 ·
175 A = 192.5 A and 1.5 · 145 A = 217 A. Normal fuses with nominal currents higher
than 192.5 A or 217 A can be used to protect the input cable; thus, 200 A or 250 A
fuses are selected depending on the use (normal or heavy-duty, respectively).
Cable Entries
Power and motor cable terminal sizes and tightening torques for the
ACS/ACC/ACP 601 with cable diameters accepted by the rubber
glands are given below. All power wiring must be rated for 60 °C
minimum
.
1)The terminals are 10mm (13/32”) bolts for attaching ring lugs (lugs not furnished).
2)IEC version. Range of cable diameters accepted by gland plate holes. For USA version conduit plate drawings, see pages B-9 and B-10.
ACx 601-0040-6 50 770 660 Bussmann 170M1564 000 170M1364 000/80
ACx 601-0050-6 63 1450 660 Bussmann 170M1565 000 170M1365 000/80
ACx 601-0060-6 100 4650 660 Bussmann 170M1567 000 170M1367 000/80
ACx 601-0070-6 100 4650 660 Bussmann 170M1567 000 170M1367 000/80
ACx 601-0100-6 125 8500 660 Bussmann 170M1568 000 170M1368 000/80
ACx 601-0120-6 200 28000 660 Bussmann 170M1570 000 170M1370 000/80
ACx 600 Type
U1,V1,W1 / U2,V2,W2 Ground (PE)
Maximum
WIre Size
Cable
Ø
mm
2)
Tightening
Torque
Maximum
WIre Size
Cable
Ø
mm
ACx 601-0005-3/0006-5
6mm
2
#10 AWG
14...20
1.5...1.8 Nm
13-18 lb.-in.
6mm
2
#10 AWG
10...14
ACx 601-0006-3/0009-5 14...20 10...14
ACx 601-0009-3/0011-5 14...20 10...14
ACx 601-0009-6/0011-6
10mm
2
#8 AWG
14...20
10mm
2
#8 AWG
10...14
ACx 601-0011-3/0016-5/0016-6 14...20 10...14
ACx 601-0016-3/0020-5/0020-6 14...20 10...14
ACx 601-0020-3/0025-5/0025-6
16mm
2
#6 AWG
14...20
16mm
2
#6 AWG
10...14
ACx 601-0025-3/0030-5/0030-6 14...20 10...14
ACx 601-0030-3/0040-5/0040-6 Cu 35mm
2
#2 AWG
Al 50mm
2
#1 AWG
20...26
8Nm
5.9 lb.-ft.
35mm
2
#2 AWG
10...14
ACx 601-0040-3/0050-5/0050-6 20...26 10...14
ACx 601-0050-3/0060-5 20...26 10...14
ACx 601-0060-3/0070-5/0060-6
70mm
2
#00 AWG
26...35 10...14
ACx 601-0070-3/0100-5/0070-6 26...35 10...14
ACx 601-0100-3/0120-5/0100-6
1)
30 Nm
22 lb.-ft.
70mm
2
#00 AWG
ACx 601-0120-3/0140-5/0120-6
ACx 601 Type
Fuses
AA
2
sVManufacturer
Type
DIN 43620
Size
Type
DIN 43653
Size
To Next Page
Loading...
