AO2000 CONTINUOUS GAS ANALYZERS | OI/AO2000-EN REV. B 359
Magnos28
Gas connections • 62, 89
Notes for calibrating • 62, 255
Operating specifications • 352
Preparation for installation • 61
Single-point calibration • 255, 256
Substitute gas calibration • 255, 258
Manual calibration • 214
Manual start of the automatic calibration • 217,
266
Material required for the installation (not
supplied) • 35
Measurement range configuration • 155
Measurement range switch-over • 155
Menu tree • 153
Message display • 140
Modbus module
Electrical connections • 107, 109, 114, 195
Modifying measurement range limits • 156, 159,
161, 178
Moving a display element from one page to
another • 204
Moving a display element within a page • 205,
206, 208, 210
N
Notes for calibrating analyzer modules • 233
Notes for network and data security • 17
Notify service • 342
Numeric keypad • 138, 142
O
Operating by key entry • 148, 209
Operating by value entry • 147, 207, 212
Operation • 127, 136
Output current response • 232
Oxygen sensor
Notes for calibrating • 72, 264
Operating specifications • 356
Preparation for installation • 71
P
Packing the gas analyzer • 344
Page overview • 199, 200, 201
Parameter overview • 199, 200, 202
Password protection • 17, 149, 180, 185, 322
Pneumatic module
Disposable filter replacement • 314, 341
Troubleshooting • 341
Power supply • 42, 122
Power supply activation • 11, 128
Power supply line connection • 107, 124
Power supply line connection – Safety notes • 121
Power supply line connection to an analyzer
module • 122
Preface • 9
Preparation for installation • 11, 34
Pressure sensor • 39
Process status • 317
Profibus module
Electrical connections • 107, 108, 114
Pump activation, pump output adjustment • 269
Purge gas flow monitoring • 23, 28, 30, 32
R
Removing a system module • 191
Replacing a system module • 190
S
Safety information • 11, 12, 13
Saving the configuration • 192
Scope of supply and delivery • 34, 73
Screen • 138, 139
Selecting user interface language • 179, 184
Setting the time zone, date and time • 137, 183
Setting up system modules • 187, 198
Softkeys • 138, 139, 144
Special requirements for operation • 25, 27
Special requirements for the operator • 12
Standard configuration • 180, 181, 317
Standard terminal connections • 114
Status LEDs • 138, 141
Status message categories • 320
Status messages • 278, 294, 297, 301, 307, 322,
337
Status messages, troubleshooting • 141, 144, 315
System bus connection • 107, 118
System status
Status messages • 317, 318
Status signals • 193, 319
T
Technical data • 22, 24, 25, 27
Test gas supply control for automatic calibration
• 216, 219
Text entry • 142, 146, 179
The 'Calibration data' sub-menu • 154, 225
The 'Function blocks' concept • 180
The 'Function blocks' sub-menu • 154, 182
U
Unpacking the gas analyzer • 11, 73
Unpacking the gas analyzer and installation • 73
Uras26
Gas connections • 66, 93
Notes for calibrating • 66, 261
Operating specifications • 354
Optical alignment • 287, 290
Phase alignment • 289, 290
Preparation for installation • 65
Troubleshooting • 340
User interface priority • 151
User page configuration • 199, 201, 203
To Next Page
Loading...
