ABB AO2000 Series User Manual

AO2000 CONTINUOUS GAS ANALYZERS | OI/AO2000-EN REV. B 357
Index
A
Access lock • 152
Active component selection • 164
Adding a component • 166, 168, 175, 177
Adding a measurement range • 159
Adding a system module • 189
Air pressure correction • 39, 271
Air pressure value correction • 39, 215, 272
Analog input module
Electrical connections • 107, 111
Analog output module
Electrical connections • 107, 110, 114
Analyzer data sheet • 75, 110, 342
Analyzer modules operating specifications • 37,
44, 46, 48, 51, 54, 57, 59, 61, 63, 65, 67, 71, 215,
346
Automatic calibration • 215, 216
Auto-ranging parameterization • 156, 161
B
Basic calibration • 273, 274, 292
C
Caldos25
Gas connections • 45, 80
Notes for calibrating • 45, 233
Operating specifications • 346
Preparation for installation • 44
Caldos25, Caldos27
Substitute gas calibration • 233, 234, 237
Caldos25, Caldos27, Magnos206
Version for the 'Safety Concept' • 23, 30, 81,
82, 88
Caldos25, Caldos27, Magnos206, Magnos28,
Magnos27
Troubleshooting • 334
Caldos27
Gas connections • 47, 82
Notes for calibrating • 47, 234
Operating specifications • 347
Preparation for installation • 46
Single-point calibration with standard gas •
234, 235
Calibrating the gas analyzer • 265
Calibration
Principles • 213
Calibration control • 213
Calibration data for automatic calibration • 214,
216, 217, 218, 227, 230
Calibration data for externally controlled
calibration • 222, 231
Calibration data for manual calibration • 215, 226
Calibration methods • 223, 226, 229, 231, 233, 234,
235, 238, 241, 251, 252, 255, 256, 259
Calibration reset • 273, 274
Cancel keys • 138, 143
Carrier gas alignment • 276
Changing a component • 166, 172
Changing analog output current range • 270
Changing module name • 179
Changing the number of decimal places • 158,
159, 178, 202
Changing the password • 150, 185
Changing the unit of a component • 177
Checking gas path seal integrity • 11, 78, 268, 295,
299, 314, 332, 334, 339, 340
Component selection list • 167, 168, 175
Configuring a component • 165, 168, 172, 175
Configuring a Modbus connection • 195
Configuring an Ethernet connection • 194
Configuring Bus I/Os • 197
Configuring key entry • 148, 200, 210
Configuring Profibus • 196
Configuring status signals • 193, 319
Configuring the bar display or point display •
200, 206
Configuring value entry • 147, 200, 208
Connecting the electrical leads • 11, 107, 126
Connecting the signal lines • 108, 110, 111, 112, 116
Cross sensitivity alignment • 275, 276
D
Deleting a component • 166, 175
Deleting a measurement range • 160
Description • 23
Digital I/O module
Electrical connections • 107, 112, 114, 188, 193,
216, 217, 220, 221, 222
Dimensional diagrams • 76, 79
Display and control unit • 138
Display features • 179, 198
Display overview • 199, 200, 201
Disposal • 345
Dynamic QR code • 315
E
Electronics module connection diagram • 107
Example
Entering and displaying the pump output •
211
Explosion-protected version for use in Class I Div.
2 explosion hazard areas • 12
Explosion-protected version with type of
protection II 3G for measurement of
flammable gases ('Safety Concept') and
non-flammable gases • 12, 44, 47, 60, 62
Explosion-protected version with type of
protection II 3G for measurement of
non-flammable gases and vapors • 12
Externally controlled calibration • 222

ABB AO2000 Series Specifications

General

Brand	ABB
Model	AO2000 Series
Category	Measuring Instruments
Language	English