Index
Service Guide N5242-90001 Index-11
Non-ANSI/NCSL Z540-1-1994
verification, 3-9
N-port calibrated measurements,
Option 551
, 2-6
O
OCXO (oven-controlled crystal
oscillator)
frequency adjustment, 3-36
theory of operation, 5-11
operating
system
recovery
, 8-18
operating environment
specifications, 3-4
verification
, 3-4
operation
13.5 GHz synthesizer boards,
5-10
26.5 GHz source boards
, 5-10
configurable test set
, 5-16
CPU board, 5-32
data acquisition
, 5-32
digital control
, 5-29
digital processor, 5-29
display assembly
, 5-31
frequency reference board
, 5-11
front panel, 5-31
front panel display board
, 5-31
hard disk drive
, 5-33
HMA 26.5, 5-11
HMA26.5
, 5-17
IF multiplexer board
, 5-22
keypad assembly, 5-31
main RAM
, 5-32
mixer brick
, 5-21
noise measurement group, 5-27
power supply
, 5-34
processing subgroup
, 5-32
receiver group
, 5-21
receiver step attenuators
, 5-21
reference mixer switch
, 5-21
signal separation group
, 5-16
source group
, 5-7
SPAM board–analog
, 5-24
SPAM board–digital
, 5-32
system motherboard
, 5-31
test port couplers
, 5-17
test set motherboard
, 5-12
operator’s check
, 3-10
accessories used in
, 3-10
description of
, 3-10
dialog box, 3-11
failure of
, 3-11
performing
, 3-10
option
analyzer, 2-3
calibration
, 2-7
data
recovering
, 8-15
repairing
, 8-15
enable utility
, 8-13
accessing, 8-13
dialog box
, 8-13
enabling and removing
, 8-14
entitlement certificate, 8-13
hardware
, 8-14
service and support
, 2-13
software, 8-14
Option 010, time domain
, 2-3
Option 020, IF inputs
, 2-4
Option 021, source 1 pulse
modulator
, 2-4
Option 022, source 2 pulse
modulator
, 2-4
Option 025, four internal pulse
generators
, 2-4
Option 029, noise figure
measurement capability
, 2-4
Option 029, noise measurement
capability
block diagram, 5-28
functional description of
, 5-6,
5-27
Option 080, frequency offset
mode
, 2-4
Option 082, scaler calibrated
converter measurements
, 2-5
Option 083, vector and scaler
calibrated frequency
converter measurements
, 2-5
Option 1CM, rack mount without
handles
, 2-5
Option 200
description of, 2-5
Option 219
description of, 2-5
Option 224
description of, 2-5
Option 400
description of, 2-6
Option 419
description of, 2-6
Option 423
description of, 2-6
Option 551
description of, 2-6
Option 897
built-in tests for commercial
calibration
, 2-6
Option 898
built-in tests for standard
compliant calibration
, 2-6
Option H08, pulsed RF
measurements
, 2-3
Option 029/219, bottom assembly
replaceable RF cables
illustrated
, 6-29
part numbers
, 6-28
Option 029/224, bottom assembly
replaceable RF cables
illustrated, 6-37
part numbers
, 6-36
Option 029/419, bottom assembly
replaceable RF cables
illustrated, 6-51, 6-55
part numbers
, 6-50, 6-54
Option 029/423, bottom assembly
replaceable RF cables
illustrated, 6-63, 6-67
part numbers
, 6-62, 6-66
Option 1A7
ISO 17025 standards compliant
calibration, 2-7
Option 200, bottom assembly
replaceable RF cables
illustrated
, 6-21
part numbers, 6-20
replaceable ribbon cables
illustrated
, 6-23
part numbers, 6-22
replaceable wire harnesses
illustrated
, 6-23
part numbers, 6-22
Option 219, bottom assembly
replaceable RF cables
illustrated
, 6-27
part numbers, 6-26
replaceable ribbon cables
illustrated
, 6-31
part numbers, 6-30
replaceable wire harnesses
illustrated
, 6-31
part numbers, 6-30
Option 219/029, bottom assembly
replaceable RF cables
illustrated
, 6-29
part numbers
, 6-28
Option 224, bottom assembly
replaceable RF cables
illustrated
, 6-35
part numbers
, 6-34
replaceable ribbon cables
illustrated
, 6-39
part numbers
, 6-38
replaceable wire harnesses
illustrated
, 6-39
part numbers
, 6-38
Option 224/029, bottom assembly
replaceable RF cables
illustrated
, 6-37
part numbers, 6-36
Option 400, bottom assembly
replaceable RF cables
illustrated
, 6-43
part numbers, 6-42
To Next Page
Loading...
