To Next PageTo Next Page
Need help?Do you have a question about the Allen-Bradley 1203 Series and is the answer not in the manual?
General| Series | 1203 |
|---|---|
| Manufacturer | Allen-Bradley |
| Input Voltage | 24V DC |
| Operating Temperature | 0°C to 55°C |
| Housing Material | Plastic |
Guide on how to use the manual's content and structure.
Defines key technical terms and abbreviations used in the manual.
Critical safety warnings for installation, operation, and maintenance.
Information on how to obtain support from Rockwell Automation.
Outlines the topics covered in the Overview chapter.
Details the types, purpose, and function of the modules.
Lists key features and capabilities of the communication modules.
Lists compatible SCANport products and controllers for the module.
Details the physical components and parts of the modules.
Lists necessary tools and equipment for installation.
Outlines the sequential steps required for setting up the module.
Outlines the topics covered in the Configuring the Module chapter.
Key safety warnings and critical information for module configuration.
Details on locating, setting, and understanding DIP switches for configuration.
Identifies the locations of DIP switches on the modules.
Lists the default switch settings for the module.
Provides a simplified guide for module configuration.
Explains how to configure Block Transfer, Logic Command, Reference, and Datalinks using SW3.
Explains settings for Starting Group, Last Rack, Fault Action, Baud Rate, and Rack Address using SW2 and SW1.
Outlines the topics covered in the Installing the Module chapter.
Guidance on choosing and using appropriate SCANport and Remote I/O cables.
Guidance on choosing and using termination resistors for the link.
Step-by-step instructions for installing the 1203-GD1/GK1 modules.
Step-by-step instructions for installing the 1336-GM1 board.
Steps to apply power and check module status LEDs after installation.
Outlines the topics covered in the Creating Ladder Logic chapter.
Explains the concept and usage of the I/O image table.
Explains basic control features and datalink functionality.
Lists products that are compatible with datalink functionality.
Details the rules, guidelines, and examples for using datalinks.
Provides examples of ladder logic programs for PLC, SLC, and Logix5550.
Provides a ladder logic program example for a PLC.
Explains the logic and structure of the PLC ladder program example.
Provides a ladder logic program example for an SLC.
Explains the logic and structure of the SLC ladder program example.
Shows how to display SLC information.
Provides a ladder logic program example for Logix5550.
Explains the logic and structure of the Logix5550 ladder program example.
Outlines the topics covered in the Using Block Transfer Messages chapter.
Explains discrete vs. block transfer methods and their usage.
Details the meaning and usage of the block transfer status word bits.
Explains data storage requirements for block transfer instructions.
Provides examples of block transfer programming for PLC, SLC, and Logix5550.
Provides examples of block transfer programming for PLC controllers.
Provides examples of block transfer programming for SLC controllers.
Explains how to calculate RIO addresses for block transfer messages.
Provides examples of block transfer programming for Logix5550 controllers.
Offers programming tips and best practices for block transfers.
Outlines the topics covered in the Troubleshooting chapter.
Identifies and describes the status LEDs on the module.
Details causes and corrective actions for specific module LEDs.
Details causes and corrective actions for the FAULT LED.
Details causes and corrective actions for the SCANport STS LED.
Details causes and corrective actions for the Health LED.
Details causes and corrective actions for the Rem I/O ACT LED.
Details causes and corrective actions for the Rem I/O STS LED.
Outlines the topics covered in the Specifications appendix.
Lists the technical specifications for the 1336-GM1 board.
Lists the technical specifications for the 1203-GD1 module.
Lists the technical specifications for the 1203-GK1 module.
Outlines the topics covered in the Supported Block Transfer Messages appendix.
Lists examples of block transfer messages and their descriptions.
Explains the structure of block transfer messages and their replies.
Details the Parameter Value Read block transfer message.
Details the Parameter Value Write block transfer message.
Details the Parameter Read Full block transfer message.
Details the Product ID Number Read block transfer message.
Details the Scattered Parameter Value Read block transfer message.
Details the Scattered Parameter Value Write block transfer message.
Details the Continuous Parameter Value Read block transfer message.
Details the Save/Recall/Initialize block transfer message functions.
Details the Fault Command Write block transfer message functions.
Details the Fault Queue Entry Read Full block transfer message.
Details the Fault Queue Size Read block transfer message.
Details the Trip Fault Queue Number Read block transfer message.
Provides a quick reference for block transfer messages.
Details block transfer messages related to trend files.
