Anrtisu Site Master S331D

To Next Page

To Previous Page

Figure 10-3 illustrates some of the key information of the E1 setup measurement display.

Chapter 10 E1 Measurements

10-5

Figure 10-3. E1 BERT Setup Measurement Display

Main Page

Default Chapter4
- Table of Contents4
Chapter 1 - General Information8
- Introduction8
- Description8
- Standard Accessories8
- Options9
- Printers10
- External Detectors10
- Optional Accessories11
- Performance Specifications13
- Preventive Maintenance19
- Calibration19
  - Instacal Module20
- Annual Verification20
- ESD Precautions20
- Mode References20
Chapter 2 - Functions and Operations22
- Introduction22
- Test Connector Panel22
- Display Overview24
- Front Panel Overview25
- Function Hard Keys26
- Keypad Hard Keys27
- Soft Keys29
- Power Monitor, External Detector (Option 5)59
- Transmission Measurement (Option 21)60
- Interference Analyzer Mode (Option 25)67
- Channel Scanner Mode (Option 27)76
- CW Signal Generator Mode (Option 28)79
- Power Meter Menus (Option 29)82
- T1 Tester Mode Menus (Option 50)84
- E1 Tester Mode Menus (Option 50)87
- Symbols89
- Self Test90
- Error Messages91
- Battery Information96
Chapter 3 - Getting Started101
- Introduction101
  - Power on Procedure101
- Cable and Antenna Analyzer Mode102
- Spectrum Analyzer Mode111
- All Modes115
- Printing119
- Using the Soft Carrying Case120
Chapter 4 - Cable and Antenna Analyzer Measurements121
- Introduction121
- Line Sweep Fundamentals121
Chapter 5 - Spectrum Analyzer Measurements130
- Introduction130
- Measurement Fundamentals130
- Preamplifier132
  - Preamplifier Operation132
  - Preamplifier Measurement Example133
- Dynamic Attenuation Control135
- Frequency Converter Interface (Option 6)136
  - Introduction136
- Selecting the Signal Standard and Channel137
  - Field Strength Measurements138
- Occupied Bandwidth139
  - Channel Power Measurement141
  - Adjacent Channel Power Ratio143
- Interference Analysis145
- AM/FM Demodulation146
  - Demodulation Procedure146
- Carrier to Interference Ratio (C/I)148
  - Procedure148
Chapter 6 - Internal Power Meter Mode151
- Introduction151
- Power Measurement151
  - Offset Calibration152
Chapter 7 - Power Monitor Mode155
- Introduction155
- Power Measurement155
Chapter 8 - High Accuracy Power Meter157
- Introduction157
- Power Measurement158
Chapter 9 - T1 Measurements161
- Introduction161
- T1 Fundamentals161
- G.821 Measurement Definitions162
- Network Equipment162
- Testing T1 Circuits164
Chapter 10 - E1 Measurements173
- Introduction173
- E1 Fundamentals173
  - G.821 Measurement Definitions174
- Network Equipment174
- Testing E1 Circuits175
Chapter 11 - Transmission Measurement184
- Introduction184
- Measuring Active Devices184
- Calibration184
- Transmission Measurement Procedure186
- Bias Tee (Option 10A)187
Chapter 12 - GPS Feature188
- Introduction188
- Activating the GPS Feature188
- Saving with GPS Information190
- Recalling GPS Information190
Chapter 13 - Interference Analyzer Mode192
- Introduction192
- Interference Analysis192
- Spectrogram192
- Signal Strength194
- Rssi195
- Signal ID196
Chapter 14 - Channel Scanner Mode197
- Introduction197
- Channel Scanner197
Chapter 15 - Signal Generator Mode200
- Introduction200
- Required Equipment200
- Procedure200
- Softkeys201
Chapter 16 - Handheld Software Tools202
- Introduction202
- Features202
- System Requirements202
- Installation203
- Using Handheld Software Tools204
Appendix A Reference Data214
- Coaxial Cable Technical Data214
Appendix B Windowing218
- Introduction218
- Examples218
Appendix C Signal Standards221
- Introduction221
- Index224

Anrtisu Site Master S331D - Page 177

Table of Contents