M Mains phase missing ..............29
mains voltage max. ..............29
mains-RTO ...................50
max. speed (async) ..............34
max. speed (sync) ...............32
Mem......................82
menu bar ....................24
Mode/Position Feedback (P) ..........56
Mode/Position Feedback (PI) .........55
Modulo-End-Pos.................67
Modulo-Start-Pos................67
Monitor1/2 ...................43
Motion task table ................66
motion task, number ..............66
Motor numbers .................98
Motor Unit (async) ...............35
Motor Unit (sync) ................33
Motorname (async)...............34
Motorname (sync) ...............32
Motornumber (async) .............34
Motornumber (sync) ..............32
MT Restart ...................47
MT_No_Bit ...................46
N Name......................30
next motion task ................73
next number ..................73
Next-InPos ...................51
NSTOP .....................45
number of the motion task ...........66
O Offline .....................25
Offset
Auto-Offset.................40
Encoder ..................37
Resolver ..................37
setpoint ..................40
Zero pulse, ROD ..............39
open ......................24
Operating systems ...............12
operation ....................14
OPMODE ...................27
Opmode A/B ..................47
oscilloscope ..................82
overspeed ...................54
P PC cable ....................13
PC connection .................13
PC software ..................29
Peak current
Iomax (async) ...............34
Iomax (sync) ................32
Ipeak ....................52
Ref.-Ipeak .................52
Phase (SERCOS) ...............90
PID-T2 .....................54
PI-PLUS ....................54
poles
motor (async) ...............34
motor (sync) ................32
Resolver ..................37
Pos latch ....................47
Pos.>x .....................50
Position.....................31
actual value ................81
Position polarity (Sercos) ...........91
position register ................68
Posreg0 ....................51
Posreg1-4 ...................51
Posreg5 ....................51
prescribed use..................6
print ......................24
print preview / print setup ...........24
Product Sercos Settings ............91
PSTOP .....................45
R ramp ......................72
Rated Speed (async)..............34
ratio ......................79
READ IDN (SERCOS) .............91
Read List Item (SERCOS) ...........91
Ref_OK, digital output .............51
reference offset ................65
Reference point
actual value ................81
reference traverse ...............58
reference traverse (homing) ..........57
Reference, digital input.............46
regen off ....................50
regen power
actual value ................81
setting ...................29
Regen resistor .................29
reset
Input ....................45
switch ...................80
resolution
oscilloscope ................82
position data ................69
Resolver ....................37
Bandwidth .................37
no. of poles ................37
Offset....................37
ROD
NI-Offset ..................39
Resolution .................38
ROD/SSI ....................46
ROD-Interpolation...............39
Rotary Direction ................53
Rotor time constant ..............34
RS232/PC, interface ..............13
run time
status ...................80
Run time ....................30
S s_cmd .....................71
save ......................24
Save
recording ..................82
save as .....................24
Save to disk ..................26
save to EEPROM ...............26
scaling, setpoints................40
screen layout ..................23
screen page
actual values ................81
amplifier ..................26
analog I/O .................40
basic setup.................29
Bode Plot .................85
communication ...............25
current ...................52
digital I/O..................44
encoder ..................38
feedback ..................36
gearing ...................79
homing ...................57
I/O expansion ...............92
Input service parameters .........84
motion task parameters ..........70
motor....................34
motor (sync) ................32
oscilloscope ................82
position (P).................56
position (PI) ................55
position data ................66
PROFIBUS.................87
PROFIBUS instrument control .......88
SERCOS..................90
SERCOS Service .............91
speed ...................53
status ...................80
terminal ..................86
102 Setup Software
Index 07/03 BECKHOFF
To Next Page
Loading...