Bennett 3000 Series - Error Codes

Bennett 3000 Spec 300 Series Instruction Manual Service & Troubleshooting
68
ERROR CODES
Error codes are displayed when there is a fault condition in the dispenser. In the event of an error, a message will be displayed
on the side of the dispenser where the error occurred. Any error message will shut down the sale but not disable the pump. To
clear an error message simply lower the handle or put the nozzle back in the boot and remove the nozzle again. To view the
error history log refer to Diagnostic Code 2 for more information. Note: Repair the problem that may have caused the error
first and then clear the message. If an error message continues to be displayed, please contact Bennett Technical Support at 1-
800-423-6638.
Continued on the next page…
Error Code
Error Text
Description
6-Digit Display
8-Digit Display
00
NO ERR
NO ERROR
No Error
02
DATA
RAM DATA
Ram Error
03
2 COLD
ATC COLD
The automatic temperature compensation probe reads less than -30

C
04
2 HOT
ATC HOT
The automatic temperature compensation probe reads less than +40

C
05
REVFLO
REV FLO
Reverse Pulser – Inactive Pulser Turning Forward or Backwards
06
RFLO A
REVFLO A
Detected Pulser A Rotating Backwards
07
RFLO B
REVFLO B
Detected Pulser B Rotating Backwards
08
RFLO C
REVFLO C
Detected Pulser C Rotating Backwards
09
RFLO D
REVFLO D
Detected Pulser D Rotating Backwards
13
PLSRAS
PULSERAS
Pulser A Error Same State Transition Limit Exceeded
14
PLSRAN
PULSERAN
Pulser A Next State Transition Limit Exceeded
15
PLSRAR
PULSERAR
Pulser A Reverse Flow
16
PLSRAD
PULSERAD
Pulser A Lead Channel Failed
17
PLSRAG
PULSERAG
Pulser A Lag Channel Failed
18
619PRA
619 PR A
Grade A was Active when the Lower CPU Stopped Responding
23
PLSRBS
PULSERBS
Pulser B Same State Transition Limit Exceeded
24
PLSRBN
PULSERBN
Pulser B Next State Transition Limit Exceeded
25
PLSRBR
PULSERBR
Pulser B Reverse Flow
26
PLSRBD
PULSERBD
Pulser B Lead Channel Failed
27
PLSRBG
PULSERBG
Pulser B Lag Channel Failed
28
619PRB
619 PR B
Grade B was Active when the Lower CPU Stopped Responding
33
PLSRCS
PULSERCS
Pulser C Same State Transition Limit Exceeded
34
PLSRCN
PULSERCN
Pulser C Next State Transition Limit Exceeded
35
PLSRCR
PULSERCR
Pulser C Reverse Flow
36
PLSRCD
PULSERCD
Pulser C Lead Channel Failed
37
PLSRCG
PULSERCG
Pulser C Lag Channel Failed
38
619PRC
619 PR C
Grade C was Active when the Lower CPU Stopped Responding
43
PLSRDS
PULSERDS
Pulser D Same State Transition Limit Exceeded
44
PLSRDN
PULSERDN
Pulser D Next State Transition Limit Exceeded
45
PLSRDR
PULSERDR
Pulser D Reverse Flow
46
PLSRDD
PULSERDD
Pulser D Lead Channel Failed
47
PLSRDG
PULSERDG
Pulser D Lag Channel Failed
48
619PRD
619 PR D
Grade D was Active when the Lower CPU Stopped Responding
51
LOPRDA
LOPROD A
Grade A Low
52
LOPRDB
LOPROD B
Grade B Low
53
FFLO A
FORFLO A
Detected Pulser A Rotating When Not Allowed
54
FFLO B
FORFLO B
Detected Pulser B Rotating When Not Allowed
55
FFLO C
FORFLO C
Detected Pulser C Rotating When Not Allowed
56
FFLO D
FORFLO D
Detected Pulser D Rotating When Not Allowed
58
619PRE
619 PR E
Grade E was Active when the Lower CPU Stopped Responding
59
BLEND
BLEND
Blend ratios sent from the console does not match the dispenser ratio.
60
POSTAL
GOPOSTAL
Mailbox has exceeded its message limits.
70
NOECAL
NO ECAL
Not Calibrated or Bad Checksum
71
RANGE
OUTRANGE
E-Cal Constant Out of Range Error
72
VINTER
VACINTER
Vapor Vacuum – Interlock Error
73
ETOTAL
ETOTFAIL
One or more electromechanical totalizer output counters are corrupted.
74
UNSEAL
UNSEALED
E-Cal Switch is in unsealed position and a normal sale started.
75
VSIDE1
VACSIDE1
Vapor Vacuum – Side 1 Error – Fast Flow or Over Current