L
Level control .................................... 221, 222
Limit value sources .................................. 231
M
Machine data ............................ 104, 105, 123
Mains connection ...................................... 60
Modulation controller ............................... 239
Monitoring
Active current ...................................... 250
Analog input signal ............................... 176
Application warning mask ..................... 190
Controller intervention .......................... 151
DC component ..................................... 151
Heat sink temperature .......................... 150
Load ................................................... 250
Motor temperature ........................ 152, 245
Output frequency ................................. 152
Overload ............................................. 150
Phase failure ........................................ 153
Warning mask ..................................... 187
Motor chopper ........................................ 251
Motor connection ...................................... 60
Motor Connection ...................................... 56
Motor potentiometer ......................... 167, 199
Motor protection ..................................... 245
Motor Protection
Motor Protection by I2t- Monitoring ....... 248
Motor temperature .................................. 252
Multi-function input ................................. 172
Multi-function output ............................... 177
Multiplexer .............................................. 206
P
Parameter identification ........................... 107
Parameter list ......................................... 275
Percentage value ramps ........................... 166
Plausibility check ..................................... 106
Positioning
Axle positioning ................................... 147
starting from reference point ................ 144
Power failure regulation ........................... 213
Pressure control ........................ 133, 220, 263
Pulse width modulation ............................ 240
PWM input .............................................. 170
R
Reference frequency channel ................... 154
Reference percentage channel .................. 158
Reference positioning .............................. 144
Reference value
Fixed frequency ................................... 161
Fixed reference value ........................... 161
JOG frequency ..................................... 162
Motor potentiometer ............................ 167
reached ............................................... 185
Reference values ..................................... 154
Fixed percentages ................................ 162
Relay output ............................................. 72
Technical data ....................................... 31
Repetition frequency input ....................... 170
Reset ....................................................... 97
S
SA Warning messages auto set-up ............ 108
Safe torque off .......................................... 23
Safety
General ................................................. 14
Safety function
Status of the inputs .............................. 259
Service ..................................................... 22
Setting frequency .................................... 184
Set-up .................................................... 116
SF Error messages auto-setup .................. 110
Slip compensation ................................... 226
Speed controller ...................................... 232
Switch-over speed-/torque control ......... 197
Speed sensor .......................................... 114
Division marks ..................................... 130
Evaluation .................................... 128, 132
Gear factor .......................................... 131
Monitoring ........................................... 253
Speed sensor connection ........................... 58
SS Status messages auto-setup ................ 108
Start anticlockwise ................................... 196
Start clockwise ........................................ 196
Starting behavior ..................................... 134
Stopping behavior ................................... 138
Storage .................................................... 20
T
Technical Data .......................................... 30
Technology Controller .............................. 216
Temperature adjustment .......................... 252
Temperature measurement ...................... 252
Thermal contact ................................. 73, 197
Three-wire control ................................... 196
Timer .............................................. 197, 201
Tolerance band ....................................... 174
Torque controller ..................................... 229
Torque Reference .................................... 230
Transport ................................................. 20
Traverse function .................................... 254
U
UL Approval .............................................. 30
User warning .......................................... 200
V
V/f-characteristic ..................................... 208
Voltage controller .................................... 211
Voltage input ............................................ 72
Volume flow control .......................... 133, 263
Volumetric flow control ............................ 220
W
Warning code
of Application warning mask ................. 191
of warning mask ........................... 188, 189
Warning mask ......................................... 187
Warning messages .................................. 273
of auto set-up ...................................... 108
Warning status ........................................ 273
Application .......................................... 273
Warranty and liability ................................. 12
X
X210A ...................................................... 71
X210B ...................................................... 71
288 Operating Instructions ACU 06/13
To Next Page
Loading...
Need help?
General
