Appendix
A-6 1070 072 143-101
PLC
Program, 4-9, 4-14, 4-19, 4-20, 4-22,
4-24, 4-26, 4-27, 4-28, 4-32
Program documentation, 1-5
Program, 1-5
Service program, 1-5
Stop time, 4-8
- personnel, V
PM, 4-2
Positioning module CC10, 3-4, 6-3, 6-6
Power failure, 4-27
Power input, 2-13, 3-3, 4-3, 6-6
Power interruption, 3-7
power interruption, 3-11, 3-16
Power source subassembly SQ16, 6-3, 6-6
Power supply, 1-6, 2-7, 2-13, 6-5
Power supply module, 2-4, 2-7, 2-12, 3-1,
3-5, 4-7, 4-26, 4-27, 4-31, 4-33, 6-1,
6-5
- NT1, 3-2
- NT2, 3-2
- NT24, 3-3
- NT3, 3-3
NT24, 6-6
PowerOn, 4-6, 4-30
Process visualisation software PV2, 1-2
Program error, 4-32
Program execution, 4-32
Program memory, 4-2
Program memory cards RAM, 3-5
Program module, 1-5, 4-2, 4-9, 4-22, 4-24,
4-28
Program structure, 1-5
Programming, 1-5
Programming error, 4-8
Programming unit, 4-19, 4-20
Protection class, 1-8
Protection standard, 1-8, 6-5
Q
Qualified personnel, V
R
R500, 3-4, 3-5, 5-4
R500P, 3-4, 3-5, 5-5
Radio interference suppression , 1-7
RAM, 4-9
Memory, 4-26, 4-27, 4-30
Range exceeded, 4-8
Reference list, 4-23, 4-28
Reference list error, 4-8
Register, 4-2
Reset, 4-5, 4-12
reset, 3-6, 3-9, 3-13, 3-18
Response time, 2-13
Restart, 4-13, 4-26, 4-27, 4-28, 4-31, 4-32
Retention, 4-5, 4-13, 4-19, 4-20, 4-26,
4-27, 4-30
Reverse polarity protection, 2-13
RM4DP, 2-5
RM4DP, 6-6
Rolling, 4-5, 4-6, 4-11
Rücksetzen, 3-14
Run, 4-20
S
Safety instructions, VII
Self-test, 4-31, 4-33
Sequential function chart, 1-5
SFC, 1-5
SKtable, 4-7, 4-33
Slot, 1-9
- AG/ZS, 2-8
- ZS400, 4-4
Power supply module, 3-8
System subassembly, 5-2
SM, 4-3, A-1
Softwareswitch S114, 4-27, 4-28, 4-30
Special marker, 4-3
- SM20.1, 3-6
Special marker management, 4-2
Specifications
- 24VLoad power supply, 6-5
- AG/ZS, 2-8
- CL400, 1-6
- fan unit, 2-13
- ZS400, 4-2
Power supply module, 3-7
Standard interfaces, 1-2
Standard operation, V
Standard peripheral devices, 1-2
Standardprogram module, 4-9, 4-22, 4-24
Standards, 1-6
Start-up block, 4-13, 4-31
Status, 4-5, 4-6