Need help?Do you have a question about the Brivis ZonePlus B061006 and is the answer not in the manual?
General| Category | Controller |
|---|---|
| Model Number | B061006 |
| Type | Zone Controller |
| Zones | 6 |
| Display | LCD |
| Power Supply | 240V AC |
| Compatibility | Brivis ducted heating systems |
Manual intended for design, installation, and commissioning of Brivis ZonePlus system.
Defines terms like 'Shall' and 'Should' used in the manual.
Important notice about the guide being a general reference and not replacing local regulations.
Defines Zone, Controlled Zone, Common Zone, Constant Zone, MTSP, and STSP systems.
Introduces NC-6 Networker, NT-1 Sensor, and Adaptive Zoning.
Primary user interface with LCD display for the system.
Zone temperature sensor with an LED indicator.
Illustrates the primary functions and interface of the NC-6 Networker controller.
Shows the physical features and connection points of the NC-6 and NT-1 units.
Lists Brivis Ducted Systems compatible with ZonePlus.
Overview of Brivis ZonePlus system and its benefits.
Explains the principles and design considerations of zoned systems.
Primary goal to maintain minimum system airflow under various zone conditions.
Outlines frameworks for MTSP and STSP systems.
Lists the procedural steps for designing a comfort system.
Guidelines for sizing ductwork and fittings according to industry standards.
Covers system design, power, wiring, and product info.
Guidelines for proper sensor placement and avoiding incorrect locations.
Recommended method for parallel wiring between NC-6 and NT-1 units.
Instructions for controller placement, backing plate removal, and wiring.
Instructions for removing the NT-1 backing plate and connecting bus cables.
How to change NT-1 jumper settings for unit identification.
Procedure for mounting the NT-1 backing plate to the wall.
Details on installing and connecting the 516 Zone Module.
Explains N-PM1 requirements and its connection to the heater.
Guidelines for installing the heater thermistor in different system types.
Wiring and operational notes for Brivis evaporative coolers with ZonePlus.
Details on zone damper requirements and the importance of insulation.
Overview of the steps required to configure the system and set parameters.
Key notes regarding default settings and system configuration.
How to adjust NT-1 jumper settings for unique sensor identification.
Crucial notes regarding wiring and the system power-up sequence.
The correct order for powering up the ZonePlus system components.
Steps to identify an NC-6 controller as a slave device.
Process for changing NC-6 sensor IDs to function as slaves.
Key considerations and the sequence for powering up systems with all NC-6 controllers.
Steps to identify multiple NC-6 controllers as slave devices.
Guide on how to access and navigate installer parameter settings.
Specific parameters related to the heater installation.
Important note regarding the configuration of parameter H01 ID07.
Guidance on the correct sequence for entering parameter values.
Configuration for single vs. multi temperature set point systems.
Details on default settings for common zones in heating and cooling.
How to assign and manage the constant zone for cooling.
Steps to enable zoning and enter zone configuration parameters.
Specific common zone settings for refrigerated cooling.
Specific common zone settings for heating.
A practical example demonstrating the setup process for Zone A.
How to customize fan speed settings for optimal airflow in each zone.
Detailed procedure for setting heating fan speeds in STSP and MTSP systems.
Detailed procedure for setting cooling fan speeds in STSP and MTSP systems.
A simplified guide to setting up the system after parameter configuration.
Essential tasks for handing over the installed system to the homeowner.
Instructions on how to set the current time and day on the Master Networker.
Guidance for the homeowner on operating the ZonePlus system.
Explains why registration is important and how to complete it.
Information on service notification messages and how to respond.
Emphasizes the importance of recorded commissioning data.
Basic principles and diagnostics for troubleshooting system faults.
Checklist for verifying system configuration and wiring integrity.
Steps to diagnose and resolve issues related to no or insufficient airflow.
Guidance for identifying and fixing airflow problems in incorrect zones.
Notes on limitations when viewing zone sensors in MTSP mode.
Addresses unit ID conflicts between NC-6 controllers and how to resolve them.
Details parameter values required for MTSP system configurations.
Details parameter values required for STSP system configurations.
To Next Page