What to do if the current output transmits a value between 0 and 4 mA from Burkert Accessories?
If the current output transmits a value between 0 and 4 mA, switch the Burkert Accessories device power supply off and then on again. If the problem persists, contact the retailer.
How to fix the value parametered for the pulse output is wrong (generated frequency is > 250 Hz) in Burkert Accessories?
Increase the value of the PU parameter.
What to do if the current output transmits 0 mA from Burkert Accessories?
If the current output transmits 0 mA, check the wiring of the current output. Also, check the fuse of the installation, replacing it if necessary, and verify the position of the sink/source switch. If the problem continues, contact the retailer.
What to do if Burkert 8045 displays «ERROR5» - output current 22 mA?
If the display shows «ERROR5» with an output current of 22 mA, especially at start-up, press ENTER, then check totalizers and calibrate the device again. If the issue persists, consider returning the device.
What to do if Burkert Transmitter programming/testing is unavailable?
If programming/testing is unavailable, it might be because internal switch 2 is locked. To resolve this, set switch 2 to 'unlock'.
What to do if Burkert 8045 Transmitter display fluctuates?
If the Burkert Transmitter display fluctuates, you can try selecting slow mode filtering. Also, if the electrodes are passivated, install the transmitter into the fluid 24 hours before use.
What to do if Burkert Accessories device is not energized?
If the Burkert Accessories device isn't energizing, check the wiring, inspect the installation's fuse and replace it if needed. Also, verify that the installation hasn't been shut down and that the power source is functioning correctly.
Why does the displayed flow rate change very slowly in Burkert Accessories?
If the displayed flow rate changes very slowly, ensure there is fluid in the pipe and try choosing a lower filter.
Why is the displayed flow rate not stable in Burkert Accessories?
If the displayed flow rate is unstable, check that there is fluid in the pipe and consider choosing a higher filter.
What to do if the displayed flow rate is not nil but the flow rate in the pipe is for Burkert Accessories?
If the displayed flow rate isn't nil when the flow rate in the pipe is, verify that the flow rate in the pipe is indeed nil, check for bubbles in the pipe, inspect the chosen filter, and calibrate the flow zero point.
General| Model | 8045 |
|---|---|
| Device Type | Transmitter |
| Measurement Principle | Electromagnetic |
| Output Signal | 4-20 mA |
| Material | Stainless steel |
| Lining Material Options | PTFE |
| Electrode Material Options | Stainless Steel, Hastelloy |
| Accuracy | ±0.5% |
| Ambient Temperature Range | -20 to 60 °C |
| Protection Rating | IP65 |
| Certifications | ATEX |
Explains warning symbols and icons used in the manual for safety and information.
Clarifies that the term "device" in this manual refers specifically to the flowmeter type 8045.
Specifies the intended use of the 8045 flowmeter for measuring liquid flow rates.
Describes the flowmeter's components, operation principle, and power supply requirements.
Lists the different versions of the 8045 flowmeter and their key specifications.
Specifies ambient conditions, humidity, altitude, and protection class for device operation.
Details the mechanical components and materials used in the flowmeter construction.
Outlines power supply, current consumption, and output specifications for the device.
Provides critical safety warnings and precautions for installation and commissioning.
Details procedures for mounting the flowmeter onto a pipe, including fitting recommendations.
Explains the electrical wiring connections and procedures for the device.
Important safety warnings related to the device's operation and handling.
Describes the Process and Configuration levels for device interaction and settings.
Explains the function of device buttons and status indicators for user interaction.
Overview of configurable parameters and how to access and adjust them.
How to select the preferred language for the device display interface.
Detailed steps for setting up the 4-20 mA analog output for flow rate measurement.
Setting DO1 to switch based on upper/lower flow rate thresholds for control or alarms.
Setting up the digital input to trigger specific device functions remotely.
Overview of diagnostic tests and calibration procedures available for the device.
Calibrating the 4-20 mA output offset and span for improved measurement accuracy.
Procedure to set the zero point for accurate flow measurements, especially after maintenance.
Critical safety warnings specific to maintenance activities and troubleshooting procedures.
Guidelines for safely cleaning the flow sensor components to maintain performance.
Comprehensive guide to resolving common issues, error messages, and LED indicators.
Troubleshooting steps for issues when the device status LED is off.
Troubleshooting steps for red LED status without explicit error messages.
Troubleshooting steps for orange LED status without explicit error messages.
Lists available spare parts, accessories, and their corresponding order codes.
To Next Page
