Canon imagePROGRAF iPF710

Other manuals for Canon imagePROGRAF iPF710

Brochure & Specs8 pages

Specification Sheet4 pages

Operations2 pages

Questions and Answers

D
Danielle MurphyJul 26, 2025
How to fix Canon imagePROGRAF iPF710 Printer that ejects blank paper?
- K
  Keith SmithJul 26, 2025
  Your Canon printer might eject blank paper because the leading edge of the roll paper was cut to straighten it. This is normal when Trim Edge First in the printer menu is On or when Trim Edge First is Automatic and the leading edge is slanted. The printer cuts the leading edge of the roll to straighten it and ejects the scraps. The printer will be ready to print after this. When Off is selected under Trim Edge First, the edge is not cut and scraps are not removed. Another possible reason is that the Printhead nozzles are clogged. In this case, print a test pattern to check the nozzles. Clean the Printhead if the nozzles are clogged.
M
Michael DavisAug 16, 2025
Why does Canon Printer display that the system is filling with ink?
- K
  Kiara MendozaAug 16, 2025
  If your Canon printer's display screen indicates that the system is filling with ink, it's likely because a cleaning operation was terminated when the printer was previously turned off. Wait until the system has been filled with ink; this process may take about ten minutes.
N
Nicole SmithNov 2, 2025
How to fix Canon imagePROGRAF iPF710 Printer connection to network?
- R
  rodriguezjasonNov 2, 2025
  If you cannot connect your Canon printer to the network, first make sure the printer is connected to the network with the correct Ethernet cable, and then turn the printer on. Ensure the Link indicator is lit. The Link indicator is green if the printer is connected via 100 Base-TX and orange if connected via 10Base-T. If the Link indicator is not lit, check the following: * Make sure the hub is on. * Make sure the end of the Ethernet cable is connected correctly. Insert the Ethernet cable until it clicks and locks in place. * Make sure there is no problem with the Ethernet cable. If there is any problem, replace the Ethernet cable. * Check the communication mode with the hub. Although the printer normally detects the hub communication mode and transmission rate automatically (in ...
J
juanhughesNov 8, 2025
What to do if Canon Printer Data lamp doesn't light up?
- W
  wkleinNov 8, 2025
  If the Data lamp on the control panel of your Canon printer does not light up, it could be due to several reasons. First, ensure the printer is turned on and the power cord is securely plugged in. Press the Power button to turn the printer on. Also, if the printer is in Sleep mode, make sure the printer is selected in the printer driver. In Windows, select the printer by clicking Select Printer or Printer in the printing dialog box and try printing again. In Mac OS X, select the printer by clicking Printer Setup Utility (or Print Center ) and try printing again. In Mac OS 9, select the printer in Chooser and try printing again. Another potential reason is that the print job is paused. In Windows, restart the print job by selecting the printer icon in the Printers and Faxes (or Printers ) w...

Summary

Safety Precautions

General Safety Warnings

Covers printer location, power supply, and emergency procedures.

Printer Handling and Environment

Guidelines on printer placement, moving, and environmental conditions.

Consumable and Component Safety

Safety notes for printheads, ink tanks, and maintenance cartridges.

imagePROGRAF Support Information

Accessing Support Information

How to access printer support information on your computer.

Support Information Content

Details of user manual and paper reference guide.

Basic Operations

Turning the Printer On and Off

Procedure for powering the printer on and off.

Loading a Roll

Instructions for loading paper rolls into the printer.

Loading Sheets Manually

Manual procedure for loading paper sheets.

Maintenance

Replacing Ink Tanks

Procedure for replacing the ink tanks.

Cleaning the Printer

Instructions for cleaning the printer's exterior and interior.

Printhead and Feed Adjustments

Checking nozzles, cleaning printhead, and adjusting alignment/feed.

Troubleshooting

Responding to Messages

List of error messages and their corrective actions.

Printing Issues and Solutions

Covers printer not printing, stopping, and quality problems.

Paper Jam Clearing

Steps to remove jammed roll paper and sheets.

Consumables

Supported Paper

Information on supported paper types for the printer.

Ink Tanks

Details about compatible ink tanks and part numbers.

Printhead and Maintenance Cartridge

Information on replacement printhead and maintenance cartridge.

Appendix

Index

Alphabetical listing of topics and page numbers.

Canon imagePROGRAF iPF710 Specifications

Printer Specifications

print resolution (max.)	2400 x 1200 dpi
line accuracy	±0.1% or Less
minimum line weight	0.02mm
number of nozzles	Matte Black: 5, 120 Nozzles, Other Colors: 2, 560 Nozzles per Color
droplet size	4 Picoliter
nozzle pitch (head resolution)	1200 dpi x Two Rows
print head swath	1.07 inch

Ink Specifications

ink type	Dye: Cyan (C), Magenta (M), Yellow (Y), Black (K); Pigment: Matte Black (MBK) – Two Channels
ink tank capacity	130ml per Color
number of colors	5

Media Specifications

media width (roll feed)	10" – 36" (254mm – 914.4mm)
media width (cut sheet)	8" – 36" (203.2mm – 914.4mm)
printable margins (roll feed)	All Sides: 0.12" (3mm) or 0" for Borderless
minimum printable media length (roll feed)	8.0" (203mm)
maximum print length (roll feed)	59' (18m)
maximum print length (cut sheet)	5.2' (1.6m)
borderless printing widths (roll media only)	10", 14", 16", 24", 36", B2 (20.28"/515mm), A1 (23.38"/594mm), B1 (28.66"/728mm), AO (33.11"/841mm)
media thickness (roll feed)	0.07 – 0.8mm (2.8 – 31.4mil)
media thickness (cut sheet)	0.07 – 0.8mm (2.8 – 31.4mil)
media core sizes	2" or 3" Core (2/3" Core Adapter Included)
maximum roll outer diameter	5.9" (150mm)

Power and Acoustic

power supply	AC 100–240V (50-60Hz)
power consumption (maximum)	140W or Less
power consumption (standby)	5W or Less (10W or less when IEEE1394 is mounted)
power consumption (power off)	1W or Less (Executive Order Compliant)
acoustic noise (operation)	52dB (A) or Less
acoustic noise (standby)	35dB (A) or Less
acoustic power	6.6 Bels or Less