EasyManuals Logo

Cisco 4451-X User Manual

Cisco 4451-X
160 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #140 background imageLoading...
Page #140 background image
6-24
Hardware Installation Guide for the Cisco 4451-X Integrated Services Router
OL-27644-01
Chapter 6 Installing and Upgrading Internal Modules and FRUs
Installing and Removing NIMs and SMs
Software Requirement for SMs
Cisco IOS XE software of a specified release or later release is required for using an SM.
To determine the version of Cisco IOS software that is running on your router, log in to the router and
enter the show version command:
Router> show version
Cisco Internetwork Operating System Software
4400 Software (C4400-ADVENTERPRISEK9-M), Version 12.3(8.2)T, INTERIM SOFTWARE
Locating an SM or NIM
See the “Locating Internal and External Slots for Modules” section on page 6-5 to locate the SM or NIM
slot on the motherboard.
Removing an SM or NIM
Use the following procedure to remove an SM:
Step 1 Read the “Safety Warnings” section on page 6-2 and disconnect the power supply before you perform
any module replacement.
Step 2 Access the SM slot. See Figure 6-2 for the various NIM and SM slot locations.
Step 3 Loosen the captive screws to open the slot cover. See Figure 6-8 and Figure 6-9.
Step 4 Pull the SM out of the connector on the motherboard. Keep the SM parallel with the motherboard to
prevent damage to the slot and standoff.
Step 5 Place the SM in an antistatic bag to protect it from ESD damage.
Installing an SM
To install an SM, use a number 2 Phillips screwdriver or flat-blade screw drive, and a 1/4-inch nut driver
or wrench.
Step 1 Read the “Safety Warnings” section on page 6-2 and disconnect the power supply before you perform
any module replacement.
Step 2 Identify the SM slot you will insert the SM into.
Step 3 Loosen the captive screws to open the slot cover. See Figure 6-8 and Figure 6-9.
Step 4 Insert the SM to the system board.
Note Be sure to press firmly on the SM until the board seats onto the connector.
Step 5 Insert the screws from the accessory kit through the SM into the standoffs. See Figure 6-20. Carefully
tighten the screws with a Phillips screwdriver (torque 6 to 8 in-lb or 0.7 to 1.1 Nm.).

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 4451-X and is the answer not in the manual?

Cisco 4451-X Specifications

General IconGeneral
Aggregate Throughput2 Gbps
Total Onboard WAN or LAN 10/100/1000 Ports4
RJ-45-based Ports4
SFP-based Ports4
Enhanced Service Module (SM-X) Slots2
NIM (Network Interface Module) Slots3
Onboard ISC Slot1
Memory (DRAM) Default4 GB
Memory (DRAM) Maximum16 GB
Flash Memory8 GB
Rack Height2 RU
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Product SeriesCisco 4000 Series
Model4451-X
Network/Transport ProtocolIPsec
Remote Management ProtocolSNMP
FeaturesFirewall protection, VPN support, Quality of Service (QoS), IPv6 support
Interfaces4 x 10/100/1000 Ethernet ports, 4 x SFP ports
PowerAC 100-240 V (50/60 Hz)
Memory4 GB
Operating Temperature0 to 40 °C
Storage Temperature-40 to 70 °C
Humidity5% to 95% non-condensing

Related product manuals