EasyManuals Logo

Cisco 4451-X User Manual

Cisco 4451-X
160 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #20 background imageLoading...
Page #20 background image
1-2
Hardware Installation Guide for the Cisco 4451-X Integrated Services Router
OL-27644-01
Chapter 1 Overview of the Cisco 4451-X Integrated Services Router
Safety Warnings
1 RJ45 Console
1 RJ45 AUX port with full modem control signals
4 10/100/1000 RJ-45 Ethernet ports (labeled GE 0/0/0, 0/0/1, 0/0/2, and 0/0/3)
4 100/1000 SFP Ethernet ports (labeled SFP 0/0/0, 0/0/1, 0/0/2, and 0/0/3)
LEDs for Ethernet and console status
LEDs for SATA hard disk drive activity and status (available on certain models)
Two DDR3 240 pin Control Plane DIMM slots which can be replaced
One DDR3 240 pin Data Plane DIMM slot which can be replaced
One compact flash slot, which is serviceable when the fan tray is removed
One 30W PoE daughter card for two of the front Gigabit Ethernet ports which can be replaced
(labeled GE 0/0/0 and 0/0/1)
One Packet Voice Digital Signal Processor Module (PVDM4) providing IP Voice and video
capability
Environment monitoring
Field replaceable fan tray
Dual redundant power supply units (PSUs) and PoE PSU.
This chapter contains the following sections:
Safety Warnings, page 1-2
Chassis Views, page 1-3
Locating the Serial Number, PID, VID and CLEI, page 1-7
Hardware Features, page 1-9
About Slots and Interfaces, page 1-17
Specifications, page 1-20
Periodic Inspection and Cleaning, page 1-25
Safety Warnings
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 4451-X and is the answer not in the manual?

Cisco 4451-X Specifications

General IconGeneral
Aggregate Throughput2 Gbps
Total Onboard WAN or LAN 10/100/1000 Ports4
RJ-45-based Ports4
SFP-based Ports4
Enhanced Service Module (SM-X) Slots2
NIM (Network Interface Module) Slots3
Onboard ISC Slot1
Memory (DRAM) Default4 GB
Memory (DRAM) Maximum16 GB
Flash Memory8 GB
Rack Height2 RU
Product TypeRouter
Form FactorRack-mountable
Connectivity TechnologyWired
Data Link ProtocolEthernet, Fast Ethernet, Gigabit Ethernet
Product SeriesCisco 4000 Series
Model4451-X
Network/Transport ProtocolIPsec
Remote Management ProtocolSNMP
FeaturesFirewall protection, VPN support, Quality of Service (QoS), IPv6 support
Interfaces4 x 10/100/1000 Ethernet ports, 4 x SFP ports
PowerAC 100-240 V (50/60 Hz)
Memory4 GB
Operating Temperature0 to 40 °C
Storage Temperature-40 to 70 °C
Humidity5% to 95% non-condensing

Related product manuals