Cisco ONS 15454 Series - Page 2

2.3.1 Figure 1-2: Mounting an ONS 15454 in a Rack◊
2.4 Mounting Multiple Nodes♦
2.5 ONS 15454 Bay Assembly♦
3 Front Door
3.1 Figure 1-3: The ONS 15454 Front Door♦
3.2 Figure 1-4: Cisco ONS 15454 Deep Door♦
3.3 Figure 1-5: ONS 15454 Front Door Ground Strap♦
3.4 Figure 1-6: Removing the ONS 15454 Front Door♦
3.5 Figure 1-7: Front-Door Erasable Label♦
3.6 Figure 1-8: Laser Warning on the Front-Door Label♦
•
4 Backplane Covers
4.1 Figure 1-9: Backplane Covers♦
4.2 Lower Backplane Cover
4.2.1 Figure 1-10: Removing the Lower Backplane Cover◊
♦
4.3 Rear Cover
4.3.1 Figure 1-11: Backplane Attachment for Cover◊
4.3.2 Figure 1-12: Installing the Plastic Rear Cover with Spacers◊
♦
4.4 Alarm Interface Panel♦
4.5 Alarm Interface Panel Replacement♦
•
5 Electrical Interface Assemblies
5.1 EIA Installation♦
5.2 EIA Configurations
5.2.1 Table 1-1: EIA Types Compatible with the 15454-SA-ANSI Only◊
5.2.2 Table 1-2: EIA Configurations Compatible with the 15454-SA-ANSI and the
15454-SA-HD
◊
♦
5.3 BNC EIA
5.3.1 Figure 1-13: BNC Backplane for Use in 1:1 Protection Schemes◊
5.3.2 BNC Connectors◊
5.3.3 BNC Insertion and Removal Tool
5.3.3.1 Figure 1-14: BNC Insertion and Removal Tool⋅
◊
♦
5.4 High-Density BNC EIA
5.4.1 Figure 1-15: High-Density BNC Backplane for Use in 1:N Protection
Schemes
◊
♦
5.5 MiniBNC EIA
5.5.1 Table 1-3: MiniBNC Protection Types and Slots◊
5.5.2 MiniBNC Connectors
5.5.2.1 Figure 1-16: MiniBNC Backplane for Use in 1:N Protection
Schemes
⋅
5.5.2.2 Table 1-4: J-Labeling Port Assignments for a Shelf Assembly
Configure with Low-Density Electrical Cards (A Side)
⋅
5.5.2.3 Table 1-5: J-Labeling Port Assignments for a Shelf Assembly
Configured with Low-Density Electrical Cards (B Side)
⋅
5.5.2.4 Table 1-6: J-Labeling Port Assignments for a Shelf Configured with
High-Density Electrical Cards (A Side)
⋅
5.5.2.5 Table 1-7: J-Labeling Port Assignments for a Shelf Configured with
High-Density Electrical Cards (B Side)
⋅
◊
5.5.3 MiniBNC Insertion and Removal Tool
5.5.3.1 Figure 1-17: MiniBNC Insertion and Removal Tool⋅
◊
♦
5.6 SMB EIA
5.6.1 Figure 1-18: SMB EIA Backplane◊
♦
5.7 AMP Champ EIA
5.7.1 Figure 1-19: AMP Champ EIA Backplane◊
5.7.2 Table 1-8: AMP Champ Connector Pin Assignments◊
♦
•
ONS_15454_Reference_Manual_R8.5.x_--_Shelf_and_Backplane_Hardware
Contents 2