ComAp InteliDrive FLX LITE

To Next Page

To Previous Page

ID-FLX Lite Global Guide

DPF Lamp

+ STOP

Active when 3697 = 1 and SPN 3701 = 5

Yellow Lamp Active when DM1 Yellow lamp is active.

Red Lamp Active when DM1 Red lamp is active.

6 back to Troubleshooting

Main Page

Table of Contents1
Document Information8
Clarification of Notation8
About this Guide8
Legal Notice8
Document History10
Language Support10
System Overview11
Warnings11
General Description11
Configurability and Monitoring12
Open Connection from Liteedit12
Open Connection from Web Browser13
Open Connection from Winscope14
Applications Overview16
Installation and Wiring17
Mounting17
Package Contents18
Software Package18
Components18
Terminal Diagram and Dimension19
Extension Plug-In Modules20
Extension Plug-In Modules Installation20
Il-Nt Aout820
Il-Nt Aio23
Il-Nt Io124
Il-Nt Bio825
Communication Modules25
Il-Nt Rs23225
Il-Nt Rs232-48526
Il-Nt S-Usb26
IB-Lite27
Il-Nt Gprs27
Remote Modules28
Il-Nt Rd (Sw)28
IL-NT RD Software Installation29
IL-NT-RD Wiring30
Igl-Ra15 (Em2Iglrabaa, Em2Fpcraeaa)30
Ib-Nt31
How to Install32
Grounding32
Wiring32
Power Supply33
Power Supply Fusing33
Binary Output Protections34
Magnetic Pick-Up34
Controller Setup36
Analog Inputs36
Table of Controller Analog Inputs36
Table of Analog Inputs Options38
Connection of Intelidrive Lite Analog Inputs40
Current Output Transducers41
Analog Input Extension Measurement41
Binary Inputs and Outputs44
Analog Outputs45
Default Analog Output Curves46
Remote Modules - CAN Bus Connection46
Connection Rules46
Front Panel Elements47
Init Screens49
Init Screen49
Firmware Screen49
Languages Screen49
User Interface Screen49
Display Menus50
Switching between User and Engineer Menus50
How to Select the Engine Mode50
How to View Measured Data50
How to View and Edit Setpoints50
How to Change the Display Contrast51
How to Check Software Revision51
How to Check the Serial Number and Choose Interface51
How to Change Language51
How to Find Active Alarms51
How to List History Records52
MEASUREMENT Screens Description52
Main Measure Screen52
Intelidrive Lite Analog Inputs Screens53
IL-NT-AIO Analog Inputs Screen53
Intelidrive Lite Binary Inputs53
Intelidrive Lite Binary Outputs53
IL-NT-BIO8 Binary Inputs Screen54
IL-NT-IO1 Binary Inputs Screen54
ECU State54
ECU Values55
Statistic55
ECU Alarmlist55
Alarm List56
Display Screens and Pages Structure57
Functions58
Engine Operation States58
OFF Mode58
MAN Mode58
Start-Stop Sequence (Simplified)58
AUT Mode60
Engine Without Pickup Operation60
Engine Timer61
MAN Mode61
AUT Mode61
Protections61
Engine RPM Control in man Mode62
Engine RPM Idle - Nominal Switching62
Engine RPM Two/Three Levels Switching63
Engine RPM by Up/Down Buttons Settings63
Engine RPM Continuous Change (Using Potentiometer)63
Speed Request Chart64
AUT Mode: Engine Load Limitation - Overview64
Functions 1 and 265
Functions 1 and 2 Setpoints66
Functions 1 and 2 Examples66
General PI Control Loop66
Engine Load Limitation with Analog Output67
General Comparator68
Engine Load Limitation with On/Off Output69
Speed Switch69
AUT Mode: Engine Regulation by RPM Control - Overview70
Functions 3 and 471
Functions 3 and 4 Setpoints72
Functions 3 and 4 Examples72
Pressure by RPM Control Via J193973
Pressure by RPM Control Via Analog Output73
Troubleshooting75
Alarm Management75
Sensor Fail (Fls)75
Warning (Wrn)75
Cooldown (CD)75
Shut down (Sd)76
List of Possible Alarms76
History File78
Record Structure78
Diagnostic Messages Read from ECU79
List of ECU Diagnostic Codes80
Tier 4 Diagnostic Codes81
Communication83
Communication84
Direct Cable Connection84
Remote Connection85
Internet Connection85
Airgate Connection85
Modem Connection85
Modbus Connection85
Modbus Step by Step85
ECU Engine Support87
Choosing the ECU to Configure87
ECU Analog Inputs88
Tier 4 Engines Support89
Technical Data90
Appendix92
Controller Objects93
List of Controller Objects Types93
Setpoints94
List of Setpoint Groups94
Password94
Enterpassword94
Changepassword94
List of Setpoints95
Group of Setpoints: Basic Settings95
Group of Setpoints: Communication Settings95
Group of Setpoints: Engine Parameters95
Group of Setpoints: Regulator95
Group of Setpoints: Load Limit95
Group of Setpoints: Engine Protection95
Group of Setpoints: Date/Time96
Group of Setpoints: Sensors Spec96
Group of Setpoints: AIO Module96
Group of Setpoints: Act. Calls/Sms97
Group of Setpoints: ATT Settings97
Group: Basic Settings98
Group: Communication Settings106
Group: Engine Parameters114
Group: Regulator129
Group: Load Limit135
Group: Engine Protection139
Group: Date/Time167
Group: Sensors Spec172
Group: AIO Module177
Group: Act. Calls/Sms181
Group: ATT Settings183
Values185
Logical Binary Inputs187
Binary Inputs Intelidrive Lite - Default Configuration187
Configuration of Binary Inputs187
List of LBI188
Logical Binary Outputs197
Binary Outputs Intelidrive Lite - Default197
List of LBO198
Extension Modules225
IL-NT RS232 (Optional Card)226
IL-NT RS232/485 (Optional Card)226
IL-NT S-USB (Optional Card)226
IB-Lite (Optional Card)226
IL-NT GPRS (Optional Card)227
IL-NT AOUT8 (Optional Card)227
IL-NT AIO (Optional Card)227
IL-NT IO1 (Optional Card)228
IL-NT BIO8 (Optional Card)228
IGL-RA15 (Remote Annunciator)228

ComAp InteliDrive FLX LITE - Page 82

Table of Contents

Related product manuals