Danfoss AK-CC55 Water Loop

To Next Page

To Previous Page

Function

Description

Values

Code

Short name

DI2 Conguration

Select the function of the digital input

0=None, 1=DI status, 2=Door function, 3=Door alarm,

4=Defrost start, 5=Main switch, 6=Night setback,

7=Thermostat band, 8=Alarm at closed, 9=Alarm at

open, 10=Case cleaning, 11=Forced cooling,

12=Open blinds, 13=Coordinated defrost, 15=Shut-

down, 16=Light control, 20=Leak detection,

24=Comp. safety, 25=Speed drive alarm, 26=Force

cond. fan ON, 29=Door fan stop

o37

o37 DI2 Cong.

Temperature sensor

type

Sensor type for S3, S4 and S5. Normally a Pt 1000 sen-

sor with great signal accuracy is used. But you can al-

so use a sensor with another signal accuracy. That

could e.g. be a PTC sensor (1000 ohm at 25 °C). All the

mounted sensors S3-S5 must be of the same type.

0=Pt 1000, 1=PTC 1000, 2=NTC 5k, 3=NTC 10k,

4=User-dened

o06

o06 SensorCong

Sensor point 1 - Temp.

The temperature value for the user-dened tempera-

ture sensor in the reference point

X20

--- SP1 Temp

Sensor point 1 - kohm

The resistance value in kohm for the user-dened

temperature sensor in the reference point

X21

--- SP1 kohm

Sensor point 1 - ohm

The resistance value in ohm for the user-dened tem-

perature sensor in the reference point

X22

--- SP1 ohm

Sensor point 2 - Temp.

The temperature value for the user-dened tempera-

ture sensor in the reference point

X23

--- SP2 Temp

Sensor point 2 - kohm

The resistance value in kohm for the user-dened

temperature sensor in the reference point

X24

--- SP2 kohm

Sensor point 2 - ohm

The resistance value in ohm for the user-dened tem-

perature sensor in the reference point

X25

--- SP2 ohm

Sensor point 3 - Temp.

The temperature value for the user-dened tempera-

ture sensor in the reference point

X26

--- SP3 Temp

Sensor point 3 - kohm

The resistance value in kohm for the user-dened

temperature sensor in the reference point

X27

--- SP3 kohm

Sensor point 3 - ohm

The resistance value in ohm for the user-dened tem-

perature sensor in the reference point

X28

--- SP3 ohm

Defrost method

Select method of defrost

0=None, 1=Electrical, 2=Hot gas, 4=Air/Ocycle

d01

d01 Def. method

Defrost stop meth-

Here you dene whether a defrost cycle is to be stop-

ped by time or by a temperature sensor

0=Time, 1=S5 sensor, 2=S4 sensor

d10

d10 DefStopSens.

Defrost stop limit A

When the selected defrost stop sensor reaches the set

limit, the defrost cycle is terminated

d02

d02 Def.StopTemp

Food type

When changing the food type the controller will auto-

matically adapt temperature setpoints and alarm lim-

its according to the selected food type. Please be

aware that the setting will revert to "None" after hav-

ing been changed.

0=None, 1=Vegetables, 2=Dairy, 3=Meat and sh,

4=Frozen food, 5=Ice cream

r89

r89 Food type

Food temp. sensor

Select the temperature to be used for the food tem-

perature representation

1=Thermostat air, 2=Alarm air, 3=S3 Air ON evap.

q39

q39 Food sensor

Network address

Network address of the controller

o03

o03 Unit addr.

DO1 Function