Danfoss VLT AutomationDrive FC 360 User Manual

[4] On reference [7] Out of current range [8] Below I low [9] Above I high [16] Thermal warning
[17] Mains out of range
[18] Reversing [19] Warning [20] Alarm (trip) [21] Alarm (trip lock)
[22] Comparator 0 [23] Comparator 1 [24] Comparator 2
[25] Comparator 3 [26] Logic rule 0 [27] Logic rule 1 [28] Logic rule 2 [29] Logic rule 3 [30] SL Time-out 0
[31] SL Time-out 1
[32] SL Time-out 2 [33] Digital input DI18
[34] Digital input DI19
[35] Digital input DI27 [36] Digital input DI29
[39] Start command [40] Drive stopped [42] Auto Reset Trip
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4 [61] Logic rule 5 [70] SL Time-out 3 [71] SL Time-out 4
[72] SL Time-out 5 [73] SL Time-out 6 [74] SL Time-out 7
[83] Broken Belt 13-52 SL Controller Action *[0] Disabled
[1] No action
[2] Select set-up 1
[3] Select set-up 2 [10] Select preset ref 0
[11] Select preset ref 1 [12] Select preset ref 2
[13] Select preset ref 3
[14] Select preset ref 4 [15] Select preset ref 5 [16] Select preset ref 6
[17] Select preset ref 7
[18] Select ramp 1 [19] Select ramp 2
[22] Run [23] Run reverse [24] Stop [25] Qstop [26] DC Brake [27] Coast
[28] Freeze output [29] Start timer 0 [30] Start timer 1
[31] Start timer 2 [32] Set digital out A low
[33] Set digital out B low
[34] Set digital out C low
[35] Set digital out D low
[38] Set digital out A high
[39] Set digital out B high
[40] Set digital out C high
[41] Set digital out D high
[60] Reset Counter A
[61] Reset Counter B
[70] Start Timer 3 [71] Start Timer 4 [72] Start Timer 5
[73] Start Timer 6 [74] Start Timer 7
14-** Special Functions 14-0* Inverter Switching 14-01 Switching Frequency [0] Ran3 [1] Ran5
[2] 2.0 kHz [3] 3.0 kHz [4] 4.0 kHz
[5] 5.0 kHz [6] 6.0 kHz [7] 8.0 kHz [8] 10.0 kHz [9] 12.0 kHz [10] 16.0 kHz
14-03 Overmodulation [0] O
*[1] On 14-07 Dead Time Compensation Level
0 - 100 *Size related
14-08 Damping Gain Factor
0 - 100 % *Size related
14-09 Dead Time Bias Current Level
0 - 100 % *Size related
14-1* Mains On/O 14-10 Mains Failure *[0] No function [1] Ctrl. ramp-down [2] Ctrl. ramp-down, trip
[3] Coasting [4] Kinetic back-up
[5] Kinetic back-up, trip
[6] Alarm [7] Kin. back-up, trip w recovery 14-11 Mains Fault Voltage Level
100 - 800 V *342 V
14-12 Response to Mains Imbalance
*[0] Trip [1] Warning [2] Disabled [3] Derate
14-15 Kin. Back-up Trip Recovery Level
0 - 500.000 ReferenceFeedbackUnit *Size related
14-2* Reset Functions 14-20 Reset Mode *[0] Manual reset [1] Automatic reset x 1
[2] Automatic reset x 2
[3] Automatic reset x 3
[4] Automatic reset x 4
[5] Automatic reset x 5
[6] Automatic reset x 6
[7] Automatic reset x 7
[8] Automatic reset x 8
[9] Automatic reset x 9
[10] Automatic reset x 10
[11] Automatic reset x 15
[12] Automatic reset x 20
[13] Innite auto reset
[14] Reset at power-up 14-21 Automatic Restart Time
0 - 600 s *10 s
14-22 Operation Mode *[0] Normal operation
[2] Initialisation 14-24 Trip Delay at Current Limit
0 - 60 s *60 s
14-25 Trip Delay at Torque Limit
0 - 60 s *60 s
14-27 Action At Inverter Fault [0] Trip *[1] Warning 14-29 Service Code
0 - 0x7FFFFFFF *0
14-3* Current Limit Ctrl.
14-30 Current Lim Ctrl, Proportional Gain
0 - 500 % *100 %
14-31 Current Lim Ctrl, Integration Time
0.002 - 2 s *0.020 s
14-32 Current Lim Ctrl, Filter Time
1 - 100 ms *5 ms
14-4* Energy Optimising 14-40 VT Level
40 - 90 % *66 %
14-41 AEO Minimum Magnetisation
40 - 75 % *66 %
14-44 d-axis current optimization for IPM
0 - 200 % *100 %
14-5* Environment 14-50 RFI Filter [0] O [1] On *[2] Grid Type 14-51 DC-Link Voltage Compensation [0] O *[1] On 14-52 Fan Control *[5] Constant-on mode
[6] Constant-o mode
[7] On-when-Inverter-is-on-else-o Mode
[8] Variable-speed mode 14-55 Output Filter
*[0] No Filter [1] Sine-Wave Filter
14-6* Auto Derate 14-61 Function at Inverter Overload *[0] Trip [1] Derate 14-63 Min Switch Frequency
*[2] 2.0 kHz [3] 3.0 kHz [4] 4.0 kHz [5] 5.0 kHz [6] 6.0 kHz [7] 8.0 kHz [8] 10.0 kHz [9] 12.0 kHz
[10] 16.0 kHz 14-64 Dead Time Compensation Zero Current
Level
*[0] Disabled [1] Enabled 14-65 Speed Derate Dead Time Compen-
sation
20 - 1000 Hz *Size related
14-8* Options 14-89 Option Detection *[0] Protect Option Cong. [1] Enable Option Change 14-9* Fault Settings 14-90 Fault Level
*[3] Trip Lock [4] Trip w. delayed reset
[5] Flystart
15-** Drive Information 15-0* Operating Data 15-00 Operating hours
0 - 0x7f. h *0 h
15-01 Running Hours
0 - 0x7f. h *0 h
15-02 kWh Counter
0 - 2147483647 kWh *0 kWh
15-03 Power Up's
0 - 2147483647 *0
15-04 Over Temp's
0 - 65535 *0
15-05 Over Volt's
0 - 65535 *0
15-06 Reset kWh Counter
*[0] Do not reset [1] Reset counter 15-07 Reset Running Hours Counter *[0] Do not reset [1] Reset counter
15-3* Alarm Log 15-30 Alarm Log: Error Code
0 - 255 *0
15-31 InternalFaultReason
-32767 - 32767 *0
15-4* Drive Identication 15-40 FC Type
0 - 0 *0
15-41 Power Section
0 - 20 *0
15-42 Voltage
0 - 20 *0
15-43 Software Version
0 - 0 *0
15-44 Ordered TypeCode
0 - 41 *0
15-45 Actual Typecode String
0 - 40 *0
15-46 Drive Ordering No
0 - 0 *0
15-48 LCP Id No
0 - 0 *0
15-49 SW ID Control Card
0 - 0 *0
15-50 SW ID Power Card
0 - 0 *0
15-51 Drive Serial Number
0 - 0 *0
15-53 Power Card Serial Number
0 - 0 *0
15-6* Option Ident 15-60 Option Mounted
0 - 30 *Size related
15-61 Option SW Version
0 - 20 *Size related
15-62 Option Ordering No
0 - 8 *Size related
15-63 Option Serial No
0 - 18 *Size related
15-70 Option in Slot A
0 - 30 *0
15-71 Slot A Option SW Version
0 - 20 *0
15-9* Parameter Info 15-92 Dened Parameters
0 - 2000 *0
15-97 Application Type
0 - 0xFFFFFFFF *0
15-98 Drive Identication
0 - 56 *0
15-99 Parameter Metadata
0 - 9999 *0
16-** Data Readouts 16-0* General Status 16-00 Control Word
0 - 65535 *0
16-01 Reference [Unit]
-4999 - 4999 ReferenceFeedbackUnit *0 ReferenceFeedbackUnit
16-02 Reference [%]
-200 - 200 % *0 %
16-03 Status Word
0 - 65535 *0
Appendix
VLT
®
AutomationDrive FC 360
70 Danfoss A/S © 03/2017 All rights reserved. MG06A702
99

Danfoss VLT AutomationDrive FC 360 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 360
Category	DC Drives
Language	English