Danfoss VLT Micro Drive FC 51 Programming Guide

Index
A
Abbreviations And Standards............................................................ 7
Active Set-up.................................................. 8, 44, 28, 11, 13, 50, 55
Alarm, Warning And Extended Status Word.............................. 65
Alarm/Warning Code List.................................................................. 64
Alarms And Warnings......................................................................... 63
Analog In/Out........................................................................................ 59
Automatic Motor Tuning (AMT)...................................................... 15
B
Brake
Resistor.................................................................................. 19, 29, 57
Resistor (ohm)................................................................................... 50
Brakes........................................................................................................ 57
C
Comm. And Options............................................................................ 60
Controllers...............................................................................................
59
Conversion Index.................................................................................. 54
Current Rating....................................................................................... 66
D
Data Readouts....................................................................................... 62
DC-brake.................................................................................... 17, 19, 28
DC-Brake.................................................................................................. 50
Digital In/Out......................................................................................... 58
Display........................................................................................................ 8
Disposal Instruction............................................................................... 4
Drive
Identification.............................................................................. 46, 47
Information........................................................................................ 61
E
Earth Leakage Current...................................................................... 3, 4
Edit Set-up.............................................................. 8, 11, 12, 13, 50, 55
Electronic Waste...................................................................................... 4
EMC............................................................................................................ 67
H
Hand Mode................................................................. 34, 11, 14, 30, 56
I
Indicator Lights........................................................................................ 9
Isolated Mains Source........................................................................... 4
IT Mains....................................................................................................... 4
L
LCP
11.............................................................................................................. 8
12.............................................................................................................. 8
Leakage Current...................................................................................... 4
Limits/Warnings.................................................................................... 58
Load
Compensation.....................................................................
16, 50, 56
Compensations................................................................................. 14
Load/Motor............................................................................................. 56
M
Main Menu..........................................................................................
9, 10
Maximum Reference........................................................................... 21
MCT 10 Set-up Software....................................................................... 1
Minimum Reference............................................................................ 21
Motor
Current.......................................................................................... 67, 15
Data....................................................................................................... 66
Direction................................................................................................ 9
Frequency........................................................................................... 15
Nominal Speed................................................................................. 15
Overload Protection.......................................................................... 4
Phase............................................................................... 48, 27, 50, 58
Power............................................................................................ 67, 14
Status.................................................................................................... 48
Temperature........................................................................ 18, 19, 50
Voltage................................................................................................. 15
N
Navigation Keys....................................................................................... 9
Not Changeable During Operation................................................
12
O
Operation Keys.........................................................................................
9
Operation/Display................................................................................ 55
Output Current...................................................................................... 66
Over-voltage Control............................................................ 20, 50, 57
P
Parameter Number................................................................................. 8
Q
Quick Menu........................................................................................ 9, 10
R
Ramp1
Ramp-down Time............................................................................ 23
Ramp-up Time...................................................................................
23
Rated Magnetizing Current.............................................................. 15
Readout Mode..........................................................................................
9
Index
VLT
®
Micro Drive FC 51 Programming Guide
MG02C602 - VLT
®
is a registered Danfoss trademark
69
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-12769-Danfoss-132F0026-VFD-Micro-Drive-440V-5HP.aspx

Danfoss VLT Micro Drive FC 51 Specifications

General

Enclosure	IP20
Output Voltage	0-100% of supply voltage
Altitude	Up to 1000 m without derating
Power Range	0.18-22 kW
Control Method	V/f
Communication	Modbus RTU
Protection Features	Over-voltage, under-voltage, over-current, over-temperature
Ambient Temperature	-10°C to 50°C
Storage Temperature	-25°C to 65°C
Relative Humidity	5-95% (non-condensing)
Input Voltage	200-240 V, 380-480 V
Braking Function	Integrated braking chopper (optional)