Datakom D-500 MK3 - Phase, 4 Wire, Star; Phase, 3 Wire, Delta

210 pages

Save Page as PDF

To Next Page

To Previous Page

D-500 MK3 User Manual Firmware V-14.2

- 42 -

5.3. 3 PHASE, 3 WIRE, DELTA

5.2. 3 PHASE, 4 WIRE, STAR

Main Page

Table of Contents6
Installation Instructions12
Mounting13
Dimensions13
Sealing, Gasket16
Electrical Installation17
Terminal Descriptions18
Battery Voltage Input18
Ac Voltage Inputs19
Ac Current Inputs20
Digital Inputs23
Analog Sender Inputs and Sender Ground23
Charge Input Terminal24
Magnetic Pickup Input24
Digital Outputs25
Mains Contactor Output25
Generator Contactor Output25
Input/Output Expansion26
J1939-Canbus Port27
Usb Device Port27
Plug-In Modules28
Modem Plug-In29
Gsm Modem Slot29
Wi-Fi SLOT30
Ethernet Slot31
Slot32
Synchronization Plug-In33
Analog Avr Control Output33
Analog Governor Control Output33
Datalink-Canbus Port34
Analog Load Share Signal35
Analog Plug-In35
Analog I/O Expansion Slot35
Mains Ct Inputs Slot36
DC Voltage & Current Slot37
Communication Slot38
Ethernet Port38
Usb Host Port39
Port40
Topologies41
Selecting the Topology41
Phase, 4 Wire, Star42
Phase, 3 Wire, Delta42
Phase, 4 Wire, Delta43
Phase, 3 Wire, Delta, 2 Ct (L1-L2)43
Phase, 3 Wire, Delta, 2 Ct (L1-L3)44
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)44
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)45
Phase, 2 Wire45
Functionalities46
Ct Location Selection46
Synchronization Functionality47
Mains Synchronization Functionality48
Single Genset Parallel with Mains49
DC Genset Functionality49
Amf Functionality50
Ats Functionality50
Remote Start Functionality51
Engine Controller Functionality52
Remote Display Unit Functionality53
400Hz Operation54
Connection Diagrams55
Genset Synchronization Functionality55
Mains Synchronization Functionality56
DC Genset Functionality58
Amf Functionality59
Ats Functionality60
Remote Start Functionality61
Engine Control Functionality62
Remote Display Panel Functionality63
Terminal Description64
Technical Specifications69
Description of Controls70
Front Panel Functionality70
Pushbutton Functions71
Display Screen Organization73
Automatic Display Scroll74
Measured Parameters76
Led Lamps77
Waveform Display & Harmonic Analysis78
Displaying Event Logs80
Statistical Counters82
Fuel Filling Counter82
Fuel Consumption Monitoring83
Operation of the Unit84
Quick Start Guide84
Stop Mode84
Auto Mode85
Run Mode, Manual Control86
Test Mode87
Protections and Alarms88
Disabling All Protections89
Service Request Alarm89
Shutdown Alarms90
Loaddump Alarms91
Warnings93
Non-Visual Warnings95
Programming96
Resetting to Factory Defaults96
Entering the Programming Mode97
Navigating between Menus98
Modifying Parameter Value99
Programming Mode Exit100
Program Parameter List101
Controller Configuration Group101
Electrical Parameters Group108
Engine Parameters Group116
Adjust Date and Time124
Weekly Operation Schedule125
Exerciser Schedule126
Sender Configuration127
Digital Input Configuration129
Output Configuration131
Site ID String133
Engine Serial Number133
Modem1-2/Sms1-2-3-4 Telephone Numbers133
Gsm Modem Parameters134
Tcp/Ip Parameters135
Sntp Parameters137
Wi-Fi PARAMETERS137
Synchronization Parameters138
DC Genset Parameters145
Snmp Parameters147
Ethernet Configuration148
Wi-Fi CONFIGURATION149
Gsm Configuration150
Crank Cutting151
Overcurrent Protection (Idmt)152
Motorized Circuit Breaker Control154
Auto Learning156
Speed & Voltage Up/Down Relay Outputs159
Speed Up/Down Control159
Voltage Up/Down Control159
J1939 Canbus Engine Support160
Dpf Regeneration Support164
DC Genset Operation165
Optimal Charging with Variable Speed165
Uncontrolled Charging with Fixed Speed167
Gps Support169
Sms Commands171
Load Transfer Modes173
Transfer with Interruption173
Uninterrupted Transfer174
Soft Transfer175
Load Sharing176
Digital Load Sharing (Datalink)177
Analog Load Sharing178
Droop Mode Operation179
Peak Lopping180
Power Export to Mains181
Distributed Power Export to Mains182
Peak Lopping with Genset Priority183
Protection Functions Paralleling with Mains184
ROCOF FUNCTION (Rate of Change of Frequency)184
Vector Shift Function184
Over/Under Frequency Function185
Over/Under Voltage Function185
Mains Reverse Power Function185
Frequency Function185
Data Recording186
Data Recording Media186
Directory Structure187
Understanding the Csv Format187
Recorded Data List, Record Period188
Software Features189
Load Shedding / Dummy Load189
Load Add / Substract190
Five Step Load Management191
Remote Start Operation192
Disable Auto Start, Simulate Mains192
Battery Charging Operation, Delayed Simulate Mains193
Dual Genset Mutual Standby Operation194
Multiple Voltage and Frequency195
Single Phase Operation195
External Control of the Unit195
Automatic Exerciser196
Weekly Operation Scheduler196
Engine Heating Operation197
Engine Idle Speed Operati̇on197
Engine Block Heater197
Fuel Pump Control198
Gas Engine Fuel Solenoid Control198
Pre-Transfer Signal198
Charging the Engine Battery199
Externally Controlled Digital Outputs199
Combat Mode199
Resetting the Controller200
Automatic Connection Topology Determination200
Zero Power at Rest201
Modbus Communications202
Parameters Required for Rs-485 Modbus Operation203
Parameters Required for Modbus-Tcp/Ip Via Ethernet203
Data Formats203
Snmp Communications206
Parameters Required for Snmp Via Ethernet207
Snmp Trap Messages207

Datakom D-500 MK3 - Phase, 4 Wire, Star; Phase, 3 Wire, Delta

Table of Contents

Related product manuals