To Next PageTo Next Page
Need help?Do you have a question about the Delta 36-6023 and is the answer not in the manual?
General| Type | Table Saw |
|---|---|
| Blade Diameter | 10 inches |
| Motor Power | 15 Amps |
| Weight | 110 lbs |
| Arbor Size | 5/8 inches |
| Max Rip Left | 12 inches |
| Voltage | 120 V |
| Max Cut Depth at 90 degrees | 3-1/8 inches |
| Max Cut Depth at 45 degrees | 2-1/4 inches |
| No-Load Speed | 5000 RPM |
| Max Rip Capacity | 30 inches |
| Max Rip Right | 30 inches |
Warnings about blade guards, riving knife, and anti-kickback devices.
Warnings about safe practices during cutting operations.
Explains kickback causes and how to avoid it.
Warnings for safe operation and maintenance procedures.
Information about California Proposition 65 warning for chemical exposure.
Details about the saw's power requirements and electrical connections.
Guidelines for selecting and using extension cords with the saw.
Lists all parts included in the package with quantities.
Lists hardware components found in various bags.
General instructions and precautions before assembling the saw.
Step-by-step guide for assembling the saw's stand.
Further steps for assembling the saw's stand components.
Final steps for assembling the stand handle and leg assembly.
Securing wheel assembly and raising stand parts.
Instructions for mounting the saw unit onto the assembled stand.
How to install the height adjustment wheel knob.
How to install the fence adjustment knob.
Steps for attaching the saw blade to the arbor.
Securing the blade assembly with washers and nuts.
Instructions for positioning the riving knife for different cuts.
How to install the throat plate into the saw table.
Details on leveling the throat plate to the table surface.
Instructions for installing the anti-kickback pawls.
Instructions for installing and removing the blade guard assembly.
Locations and methods for storing saw accessories on the tool.
Pre-operation checklist for safety and readiness.
Guidance on preventing and responding to kickback incidents.
Connecting a dust collection system to the saw.
How to operate the power switch and lock it out.
Steps for folding and moving the table saw.
General warnings and safety guidelines for all cutting operations.
Visual examples of different types of cuts possible with the saw.
Detailed instructions for performing rip cuts.
Instructions for performing rip cuts with a beveled blade.
Detailed instructions for performing cross cuts.
Instructions for performing cross cuts with a beveled blade.
Instructions for making miter cuts using the miter gauge.
Instructions for performing cuts combining bevel and miter angles.
Guidance on supporting and cutting large panels.
Information on making grooves and rabbets.
Step-by-step guide for performing non-through cuts.
How to align the blade parallel to the miter gauge groove.
Information about using and constructing a push stick.
How to add an auxiliary facing to the miter gauge.
Instructions for making and using a push block.
Using featherboards for grooving and rabbeting safety.
How to make and use featherboards for workpiece control.
Using a clamp as a cut-off gauge for repetitive crosscuts.
General advice on using specialized jigs for cuts.
How to install and level the throat plate.
How to ensure the blade is perpendicular to the table surface.
How to adjust the 0 and 45-degree positive stops for bevel cuts.
How to raise and lower the saw blade for cutting.
Steps for changing the blade's bevel angle.
How to use the miter gauge for cross and miter cuts.
Instructions for attaching the rip fence to the table.
How to detach the rip fence from the table.
Using the black scale on the fence for rip cuts.
Using the extension wing with the black scale.
Using the white scale on the fence for rip cuts.
Using the extension wing with the white scale.
Using the blue scale on the fence for rip cuts.
Using the extension wing with the blue scale.
How to adjust the fence rail system for accurate cuts.
How to use the workpiece support for large materials.
How to adjust the riving knife height for different cuts.
Step-by-step guide to adjust the riving knife position.
How to align the riving knife parallel to the saw blade.
How to correct horizontal misalignment of the riving knife.
How to correct vertical misalignment of the riving knife.
Instructions for cleaning the saw and its components.
Key maintenance tasks and areas to check regularly.
Guidance for diagnosing and resolving common machine issues.
Information on obtaining parts, service, and warranty support.
How to identify and order replacement parts.
How to get replacement safety labels.
Information on servicing, repairs, and contacting support.
