To Next Page
M
morenoanthonyAug 25, 2025
What to do if my Denon AVR-1312 display is off?
- JJohn WaltonAug 25, 2025
If the display on your Denon Stereo Receiver is off, set “Display” on the menu to something other than “OFF”.
What to do if my Denon AVR-1312 display is off?
If the display on your Denon Stereo Receiver is off, set “Display” on the menu to something other than “OFF”.
Why is there no sound from the surround speaker of my Denon AVR-1312 Stereo Receiver?
If there is no sound coming from the surround speakers of your Denon Stereo Receiver, ensure that the surround speakers are connected to the SURROUND terminals.
Why is there no sound from the surround back speaker of my Denon Stereo Receiver?
If you're not getting any sound from the surround back speaker on your Denon Stereo Receiver: * Set “Speaker Config.” – “Surround Back” on the menu to something other than “None”. * Ensure the surround mode is set to something other than “STEREO” and “VIRTUAL”.
Why is there no sound from the subwoofer of my Denon Stereo Receiver?
If there's no sound coming from the subwoofer connected to your Denon Stereo Receiver: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”. * If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “SW Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
How to fix reception failures, noise or distortion on Denon Stereo Receiver?
To address reception failures, noise, or distortion on your Denon Stereo Receiver: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna separate from other connection cables.
What to do if after turning on the power, the power indicator is blinking red on my Denon Stereo Receiver?
If, after turning on your Denon Stereo Receiver, the power indicator is blinking red, it indicates a failure in the unit's amplifier circuit. Turn off the power and contact a DENON service advisor.
Why is there no audio output from my Denon Stereo Receiver?
If audio is not coming from your Denon Stereo Receiver, verify that all device connections are secure and that the speaker connections are correctly configured. Ensure the audio device is powered on, the master volume is appropriately adjusted, and mute mode is off. Select the correct input source and mode. Also, remember that no sound will come from the speakers or PRE OUT connectors when headphones are connected, so disconnect them.
How to troubleshoot no audio output with HDMI on Denon AVR-1312?
If you're experiencing no audio output with an HDMI connection on your Denon Stereo Receiver, first check the HDMI connector connections. If you want audio from the speakers, set “HDMI Audio Out” to “Amp” in the menu. If you want audio from the TV, set “HDMI Audio Out” to “TV” in the menu.
Why is there no sound from the subwoofer on my Denon AVR-1312 Stereo Receiver?
If your Denon Stereo Receiver isn't producing sound from the subwoofer, check the subwoofer connections and ensure the subwoofer is powered on. In the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes”. Note that if “Front” and “Center” for “Speaker Config.” are set to “Large”, and “SW Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
What to do if my Denon AVR-1312 Stereo Receiver does not turn on?
If your Denon Stereo Receiver does not turn on: * Verify that the power plug is correctly inserted into the power outlet. * The protection circuit might be active. Disconnect the power plug from the electrical outlet, wait 5 to 10 seconds, and then re-insert it.
General| Number of Channels | 5.1 |
|---|---|
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Amplification Type | Discrete |
| Input Sensitivity | 200 mV |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Signal-To-Noise Ratio | 98 dB |
| Digital Optical Inputs | 2 |
| Coaxial Digital Input | 1 |
| Analog Audio Inputs | 4 |
| Headphone Jack | Yes |
| Tuner Presets | 56 |
| Dimensions (W x H x D) | 434 x 151 x 319 mm |
| Amplifier Type | Discrete |
| Tuner Type | AM/FM |
| Preset Stations | 56 |
| Remote Control | Yes |
| Dolby Technologies | Dolby Digital Plus, Dolby Pro Logic II, Dolby TrueHD |
| DTS Technologies | DTS-HD Master Audio |
| Output Power / Channel | 75 W (8 Ohms, 20 Hz - 20 kHz, 2 channels driven, THD 0.08%) |
| Input Impedance | 47 kOhms |
| Audio Inputs | 2 Optical, 1 Coaxial, 4 Analog |
| Power Output | 75W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
Important warnings for safe operation and to prevent damage to the unit.
Statement of compliance with EU directives and standards for product safety.
Information on proper disposal of packaging and the unit.
Guidelines for safe and effective installation to ensure proper heat dissipation and operation.
Precautions for safe handling, power, condensation, mobile phone interference, and moving the unit.
Explains how to connect various audio and video devices to the unit.
Covers basic playback functions like selecting sources and adjusting volume.
Guide to choosing different surround sound modes for an immersive audio experience.
Advanced methods for speaker setup and connection for optimal surround sound.
Advanced playback features and operations beyond basic functions.
Comprehensive guide to configuring various settings via the menu system.
Advanced configurations like video signal format switching.
Identification and explanation of front and rear panel controls and indicators.
Solutions for common problems and operational issues encountered with the unit.
Technical details and performance characteristics of the AV receiver.
