Denon AVR-X3000 User Manual

139
Appendix
TipsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Settings
Audyssey
Set Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey
Dynamic Volume®. These can be selected after Audyssey® Setup has been
performed. For additional information on Audyssey technology, please see
page213.
%
•“MultEQ® XT”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each
input source.
•“MultEQ® XT”, “Dynamic EQ” and “Dynamic Volume” cannot be set when the
sound mode is set to “DIRECT” or “PURE DIRECT”.
2 MultEQ
®
XT
MultEQ® XT compensates for both time and frequency characteristics
of the listening area based on Audyssey® Setup measurement results.
Selection is done from three types of compensation curves. We
recommend the “Audyssey” setting.
Audyssey (Default) : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Graphic EQ : Apply frequency response set with “Graphic EQ”
(vpage142).
O : Turn “MultEQ® XT” equalizer o.
%
•When using headphones, “MultEQ® XT” is automatically set to “O”.
2 Dynamic EQ
Solves the problem of deteriorating sound quality as volume is
decreased by taking into account human perception and room
acoustics. Works with MultEQ® XT.
On (Default) : Use Dynamic EQ.
O : Do not use Dynamic EQ.
%
•When the menu “Dynamic EQ” setting is “On”, it is not possible to do “Tone
Control” (vpage137) adjustment.

Denon AVR-X3000 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	135 W
Power output per channel (20-20KHz@8 Ohm)	105 W
HDMI in	7
Audio (L/R) in	5
Composite video in	3
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
AM band range	520 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Black
Audio decoders	DTS Neo:X, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	600 W
Cables included	AC

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	10700 g