Denon AVR-X3000 User Manual

165
Appendix
TipsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Settings
Distances
Set distance from listening position to speakers.
Measure beforehand the distance from the listening position to each
speaker.
2 Unit
Set the unit of distance.
Feet (Default)
Meters
2 Step
Set the minimum variable width of the distance.
1ft (Default) / 0.1ft
0.1m / 0.01m
2 Set Defaults
The “Distances” settings are returned to the default settings.
2 Set the distance
0.0ft – 60.0ft / 0.00m – 18.00m
%
•The speakers that can be selected dier depending on the “Amp Assign”
(vpage162) and “Speaker Config.” (vpage163) settings.
•Default settings :
Front L / Front R / F. Height L / F. Height R / F. Wide L / F. Wide R / Center /
Subwoofer : 12.0 ft (3.60 m)
Surround L / Surround R / Surr.Back L / Surr.Back R : 10.0 ft (3.00 m)
•Set the dierence in the distance between the speakers to less than 20.0 ft
(6.00 m).
Levels
Set the volume of the test tone to be the same when it is output from
each speaker.
2 Test Tone Start
Output test tone. A test tone is output from the selected speaker.
While listening to the test tone, adjust the volume output from the
selected speaker.
–12.0dB – +12.0dB (Default : 0.0dB)
%
•When “Levels” is adjusted, the adjusted values are set for all the sound
modes.
•When headphones are connected to the PHONES connector on this unit, you
cannot set “Levels”.
2 Set Defaults
The “Levels” settings are returned to the default settings.

Denon AVR-X3000 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	135 W
Power output per channel (20-20KHz@8 Ohm)	105 W
HDMI in	7
Audio (L/R) in	5
Composite video in	3
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
AM band range	520 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Black
Audio decoders	DTS Neo:X, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	600 W
Cables included	AC

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	10700 g