Denon AVR-X3000 User Manual

153
Appendix
TipsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Settings
Speakers
The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically. This is called
“Audyssey® Setup”.
You do not have to perform Audyssey® Setup when you have already performed Speaker Calibration in Setup Assistant.
To set up the speakers manually, use “Manual Setup” (vpage162) on the menu.
Audyssey
®
Setup
To perform measurement, place the Setup and measurement microphone
in multiple locations all around the listening area. For best results, we
recommend you measure in six or more positions, as shown in the
illustration (up to eight positions).
%
•When performing Audyssey® Setup, Audyssey MultEQ® XT/Audyssey Dynamic
EQ®/Audyssey Dynamic Volume® functions become active (vpage139, 140).
NOTE
•Make the room as quiet as possible. Background noise can disrupt the room
measurements. Close windows and turn o the power on electronic devices
(TVs, radios, air conditioners, fluorescent lights, etc.). The measurements could be
aected by the sounds emitted by such devices.
•During the measurement process, place cell phones outside the listening room.
Cell phone signals could disrupt the measurements.
•Do not stand between the speakers and Setup and measurement microphone or
allow obstacles in the path while the measurements are being made. Do not hold
the Setup and measurement microphone in your hand during measurements. This
will cause inaccurate readings.
•During the measurement process, audible test tones will come from the speakers
and subwoofer(s), but this is part of normal operation. If there is background noise
in the room, these test signals will increase in volume.
•Operating VOLUME
df on the remote control unit or MASTER VOLUME on the
main unit during the measurements will cancel the measurements.
•Measurement cannot be performed when headphones are connected. Unplug the
headphones before performing Audyssey® Setup.

Denon AVR-X3000 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	135 W
Power output per channel (20-20KHz@8 Ohm)	105 W
HDMI in	7
Audio (L/R) in	5
Composite video in	3
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
AM band range	520 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Black
Audio decoders	DTS Neo:X, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	600 W
Cables included	AC

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	10700 g