Denon AVR-X5200W

Error
Code
DPMS Update Error Display Details of Error code Coping strategies
5B
S u b * * * m i n
U p d a t i n g f a i l 5 B
NACK received in response or no
response from Sub for L com-
mand.
Turn on the power again. Update will
start automatically.
5C
S u b * * * m i n
U p d a t i n g f a i l 5 C
No Update Packet received from
CX870 / CY920 (Time Out).
Turn on the power again. Update will
start automatically.
5D
S u b * * * m i n
U p d a t i n g f a i l 5 D
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Turn on the power again. Update will
start automatically.
5E
S u b * * * m i n
U p d a t i n g f a i l 5 E
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Turn on the power again. Update will
start automatically.
5F
S u b * * * m i n
U p d a t i n g f a i l 5 F
Setup failure of the transfer
method of XModem.
Turn on the power again. Update will
start automatically.
60
S u b * * * m i n
U p d a t i n g f a i l 6 0
NACK received in response or no
response from Sub for "P" com-
mand.
Turn on the power again. Update will
start automatically.
61
S u b * * * m i n
U p d a t e C h e c k N G 6 1
Mismatched Check Sum in re-
sponse or no response from Sub
for "I" command.
Turn on the power again. Update will
start automatically.
62
S u b * * * m i n
U p d a t i n g f a i l 6 2
Failed to start up Sub in Power On
sequence during Update.
Turn on the power again. Update will
start automatically.
80
G U I * * * m i n
U p d a t i n g f a i l 8 0
Write Enable Latch Bit not set in
Read after issuing WREN com-
mand.
Turn on the power again. Update will
start automatically.
81
G U I * * * m i n
U p d a t i n g f a i l 8 1
Block Erase failed in Read after
issuing BE command.
Turn on the power again. Update will
start automatically.
82
G U I * * * m i n
U p d a t i n g f a i l 8 2
No Update Packet received from
CX870 / CY920 (Time Out).
Turn on the power again. Update will
start automatically.
83
G U I * * * m i n
U p d a t i n g f a i l 8 3
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Turn on the power again. Update will
start automatically.
84
G U I * * * m i n
U p d a t i n g f a i l 8 4
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Turn on the power again. Update will
start automatically.
85
G U I * * * m i n
U p d a t i n g f a i l 8 5
Setup failure of the transfer
method of XModem.
Turn on the power again. Update will
start automatically.
86
G U I * * * m i n
U p d a t i n g f a i l 8 6
Mismatched Check Sum in Check
Sum comparison after rewriting.
Turn on the power again. Update will
start automatically.
A0
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 0
IP Address acquisition failure
(AutoIP).
Check the network connection. Update
in an environment where there is a
small network load.
92