Denon AVR-X6200W - Diagnostic Mode (Service Path Check Mode); 2-1.1. Actions; 2-1.2. Starting up; 2-1.3. Canceling diagnostic mode

2-1DIAGNOSTICMODE(ServicePathCheckMode)
2-1.1.Actions
This function is convenient for conrming problem paths in the product and executing a path check after repair.
The Video and Audio paths can be checked.
The backup data is not rewritten.
2-1.2.Startingup
Hold down buttons "STATUS" and "ZONE3SOURCE" at the same time and press the power button to turn on the power.
Select
"1.SERVICECHECK" and press the "ENTER" button to start the diagnostic mode.
The "TUNED", "STERO" and "RDS" segments are lit in this mode.
2-1.3.Cancelingdiagnosticmode
Press the power button to turn off the power.
2-1.4.Selectingitems
Press
q
button to switch between video items and audio items.
Press button
w
or
e
to select the previous or next item.
The unit Remote control unit
Actions
q w e q w e
Audio ⇔ Video PREVIOUS NEXT Audio ⇔ Video PREVIOUS NEXT
Button DIMMER CURSOR
0
CURSOR
1
SLEEP CURSOR
0
CURSOR
1
2-1.5.Audiosystemconrmationitems
g. XX: See the block diagram of the g.XXth.
Pathsconrmationitem Display Settings ContentsofconrmationRemarks
1
Analog
(MAIN ZONE)
A 0 1 : A N A L O G P A S S
Input Source : CBL/SAT
Input Mode : Analog (xed)
Amp assign : 9.1ch
Floor Layout : 5.1 & Surround Back
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
・Analog input ⇒ Speaker output (Front L/R)
・Analog input ⇒ Preout output (Front L/R)
(
b
As the input source, you can switch from CBL/SAT to other ones.)
2
Digital
(MAIN)
A 0 2 : D I G I T A L
Input Source : CBL/SAT
Input Mode : Digital (xed)
Sound mode : Multi Ch Stereo
Vol. : 60.0 (-20.0dB)
Amp assign : 9.1ch
Floor Layout : 5.1 & Surround Back
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
Speaker Select : Floor
Speaker Cong : All Speaker = Small/Subwoofer = 2spkrs
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
・Digital input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・Digital input ⇒ Preout output (Front L/R, Center, Subwoofer1/2, Surround L/R, Surround Back L/R)
(
b
As the input source, you can switch from CBL/SAT to other ones.)
3
Digital (signal) Path
(ZONE2)
A 0 3 : D I G I T A L - Z 2
Input Source : Online Music
Input Mode : Auto
Sound mode : Stereo
Amp assign : 7.1ch + ZONE2
Speaker for ZONE2 : Surround Back
Floor Layout : 5ch
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
・Digital (PCM) input ⇒ Speaker output (Surround Back L/R → ZONE2 L/R)
・Digital (PCM) input ⇒ Preout output (ZONE2 L/R)
(
b
As the input source, you can switch from Online Music to other ones.)
g.01
g.02a
g.02b
g.03a
g.03b
g.03c
26