EasyManua.ls Logo

Dick SM-200 TE - User Manual

Default Icon
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Friedr. Dick GmbH & Co. KG · PO Box 1173 · 73777 Deizisau · GERMANY
Tel.: +49 (0)7153-817-0 · Fax: +49 (0)7153-817-218/-219 · Web: www.dick.de · E-mail: mail@dick.de ·
No. 9 8320 4252 Vers.2 / 11-2017
Operating Instructions (Translation)
SM-200 TE
3~400 V - 50-60 Hz
Grinding and Honing Machine
Art. No. 98320005 with a universal grinding arm
Art. No. 98320000 with a radial grinding arm
GB

Table of Contents

Questions and Answers

  • L
    Louis AguilarAug 15, 2025
    Why is my Dick SM-200 TE motor and pump not working?
    • G
      Gerald HernandezAug 15, 2025
      If the motor and pump of your Dick Power Tool aren't working, first, ensure the power supply is properly connected to the mains and matches the machine's data. Inspect the power lines and connections for any damage. Remember to disconnect the machine from the power supply before checking. Also, verify that the belt safety guard is correctly mounted and the magnetic bar is attached. If the issue persists, the main On/Off switch may be defective and needs checking.
  • C
    Christina BatesAug 18, 2025
    What to do if there is no cooling water in my Dick SM-200 TE?
    • J
      James JohnsonAug 18, 2025
      If your Dick Power Tool has no cooling water, start by refilling the water tank, cleaning it if necessary. Ensure the pump is connected to the designated socket on the machine and the valve is open. Also, inspect the water pipe for any blockages or defects, cleaning the pump filter and replacing any faulty water-bearing components. If problems persist, check the power supply and consider replacing the pump.
  • A
    amandasanchezAug 22, 2025
    How to fix insufficient torque and whistling noise on Dick SM-200 TE Power Tool grinding belt?
    • S
      susangarciaAug 22, 2025
      If you're experiencing insufficient torque on the grinding belt or polishing wheel of your Dick Power Tool accompanied by a whistling noise, the V-ribbed belt likely needs attention. Try increasing the tension of the V-ribbed belt. If the belt is worn, replace it. Also, check for any dirt blocking the free running of the discs and clean them.
  • R
    Roberta McdanielAug 26, 2025
    Why is there insufficient torque on the grinding wheel of my Dick SM-200 TE?
    • J
      John RamirezAug 26, 2025
      If your Dick Power Tool exhibits insufficient torque on the grinding wheel, grinding belt, or polishing wheel, the V-belt might be the issue. Try re-tensioning the V-belt. If the V-belt is worn, replace it. If neither of these steps resolves the issue, a component defect may be present, and you should replace the defective component.
  • A
    Anthony SparksAug 28, 2025
    How to troubleshoot a Dick SM-200 TE grinding angle device that won't move?
    • J
      John RamosAug 28, 2025
      If the grinding angle device on your Dick Power Tool cannot be moved, first ensure the connection with the neutral conductor. In power networks without a neutral connector, connect to the earth in the neutral conductor socket. Be aware that this overrides a safety function. Check the lift rod for damage or contamination. Ensure the foot pedal connector is properly plugged in. If the issue persists, arrange for a qualified electrician to remedy the fault, as a component may be defective.
  • G
    Gina VanceSep 1, 2025
    What causes a Dick Power Tool grinding belt to not adjust?
    • R
      rogerskarenSep 1, 2025
      If the grinding belt on your Dick Power Tool cannot be adjusted, it may be due to a worn deflection pulley, requiring replacement. Alternatively, the mechanics might be sluggish or defective, necessitating repair. Another possibility is a worn contact wheel, which would also need replacing.
  • C
    Cynthia SmithSep 4, 2025
    Why is my Dick Power Tool making unusual noises?
    • J
      Jill Parker DDSSep 4, 2025
      If your Dick Power Tool is producing increased and unusual noises, it could indicate component damage, such as bearings or a loose screw connection. Localise the source of the noise and replace the defective component if necessary.
  • K
    Karen RileySep 7, 2025
    What to do if the grinding belt on my Dick SM-200 TE Power Tool cannot be tensioned?
    • B
      Brittney PadillaSep 7, 2025
      If the grinding belt on your Dick Power Tool cannot be tensioned, the mechanics are likely sluggish or defective and need repair.
  • A
    Andrew MorrisSep 12, 2025
    Why is there play in the lifting device of my Dick Power Tool?
    • D
      Daniel Mills DVMSep 12, 2025
      If there is play in the lifting device of your Dick Power Tool, it could be due to wear on the wedge, which needs tightening. Alternatively, there might be wear on the guidance, requiring replacement of the assembly.

Dick SM-200 TE Specifications

General IconGeneral
BrandDick
ModelSM-200 TE
CategoryPower Tool
LanguageEnglish