either in input or in output.
456 CONDITIONED VEHICLE VEHICLEb:XXXXXXXXXXXXXXXXXXXX + T
in which XXXXXXXXXXXXXXXXXXXX are the 20 description characters; only the entered characters are printed,
expanding from left to right; if the vehicle is not selected, the block is ignored. The block can just be printed once,
either in input or in output.
457 ONLY VEHICLE WEIGHS XXXXX + T
in which XXXXX is the number of the total weighs relative to the selected vehicle.
458 ENTERED TOTAL VEHICLE IN.bTOTALb:bXXXXXXXXUM + T
in which XXXXXXXX is the total of the UNLOADED weight relative to the selected vehicle.
459 EXITED TOTAL VEHICLE OUT.bTOTALbb:bXXXXXXXXUM + T
in which XXXXXXXX is the total of the LOADED weight relative to the selected vehicle.
460 NET TOTAL VEHICLE NETbTOTALb:bXXXXXXXXUM + T
n which XXXXXXXX is the difference between the ENTERED TOTAL and the EXITED TOTAL relative o the
selected vehicle.
461 JUST TEXT “VEHICLE” VEHICLEb:
462 JUST TEXT “VEHICLE TOTAL” VEHICLE TOTAL + T
463 CANCELLATION OF FREE TEXT CONTENTS
After their printing, ALL the contents of the free texts present are cancelled.
464 CUSTOMER DESELECTION
After its printing, the present customer is deselected.
465 MATERIAL DESELECTION
After its printing, the present material is deselected.
466 VEHICLE DESELECTION
After its printing, the present vehicle is deselected.
NOTE: It is advisable to enter the deselection macros as last commands before the print end.
467 LAST TARE ON ALIBI MEMORY XXXXXXXXXX
468 SCALE 1 WEIGHT FOR “A+B” B1bbbbXXXXXXXXXXUM + T
The macro is printed if scale 1 or the sum of scales is displayed.
469 ONLY SCALE 1 WEIGHT FOR “A+B” XXXXXXXXXX
470 SCALE 2 WEIGHT FOR “A+B” B2bbbbXXXXXXXXXXUM + T
The macro is printed if scale 1 or the sum of scales is displayed.
471 ONLY SCALE 2 WEIGHT FOR “A+B” XXXXXXXXXX
472 WEIGHT SUM FOR “A+B” B1+B2bXXXXXXXXXXUM + T
The macro is printed if the sum of the scales is displayed.
473 ONLY WEIGHT SUM FOR “A+B” XXXXXXXXXX
474 ONLY INPUT WEIGH DATA GG/MM/AA
475 ONLY INPUT WEIGH TIME HH:MM
476 PERCENT VALUE OF WEIGHT INCREMENT/DIMINUTION COMPARED WITH THE INITIAL WEIGHT XXX.X
NOTA: if the printing characters are not set with 617 macro or the values are incorrect (decimal number > characters
number), the percent value is always printing on 5 characters, including decimal point and one decimal number.
477 JUST 2
nd
MATERIAL CONDITIONED DESCRIPTION XXXXXXXXXXXXXXXXXXXX + T
in which XXXXXXXXXXXXXXXXXXXX are the 20 description characters; only the entered characters are printed,
expanding from left to right. The block is printed only once, either in input or output.
478 JUST 2
nd
MATERIAL CONDITIONED HEADING DESCRIPTION2
479 JUST 2
nd
MATERIAL DESCRIPTION XXXXXXXXXXXXXXXXXXXX
in which XXXXXXXXXXXXXXXXXXXX are the 20 description characters; just the entered characters are printed,
expanding from left to right; if the material is not selected, the block is ignored. The block can be printed several
times, either in input or in output.
480 JUST PLATE VALUE XXXXXXXXXX
if the vehicle is not selected, the block will be ignored. The block can be printed several times, either in input or in
output.
481 PRINTS TERMINATOR CR, CRLF, LF or NO TERMINATOR
482 PRINT CALCULATED DATA XXXXXXXXXX
483 PRINT FIRST ENTERED DATA XXXXXXX
484 PRINTS SECOND ENTERED DATA XXXXXXX
To Next Page
Loading...
Need help?
General
