INDEX
1. REQUIREMENTS FOR AN OPTIMAL INSTALLATION ...................................................................................................................... 4
1.1 ELECTRICAL PRECAUTIONARY MEASURES ............................................................................................................................ 4
1.1.1 CABLE CLASSIFICATION ................................................................................................................................................. 5
1.1.2 RECOMMENDED DISTANCES AMONG CABLES ........................................................................................................... 5
1.1.3 MAXIMUM CABLE LENGTH .............................................................................................................................................. 5
1.2 EARTHING SYSTEM .................................................................................................................................................................... 6
2. CONNECTION TO THE LOAD RECEIVER .......................................................................................................................................... 9
2.1 ANOLOG LOAD CELLS ................................................................................................................................................................ 9
CONNECTION TO STANDARD “DINI ARGEO” FEMALE CONNECTOR ........................................................................................ 10
2.2 DIGITAL LOAD CELLS ................................................................................................................................................................ 10
2.3 CONNECTION OF LOAD CELLS TO INDICATOR ..................................................................................................................... 11
2.3.1 C16i DIGITAL CELL CONNECTION ............................................................................................................................... 12
2.3.2 RCD DIGITAL CELL CONNECTION ............................................................................................................................... 13
3. SETUP ENVIRONMENT ..................................................................................................................................................................... 14
3.1 SET-UP ENVIRONMENT BLOCK DIAGRAM ............................................................................................................................. 16
3.2 DESCRIPTION OF THE STEPS ................................................................................................................................................. 22
<< LAnG >> FIRMWARE LANGUAGE .................................................................................................................................... 22
<< nuM.SCA >> NUMBER OF CONNECTED SCALES (*)...................................................................................................... 22
<< F.ModE >> SCALE FUNCTIONING ................................................................................................................................... 23
<< SEtuP >> SCALE CONFIGURATION ................................................................................................................................. 32
<< diAG. >> DIAGNOSTICS MENU ......................................................................................................................................... 48
3.3 CALIBRATION OF THE SCALE .................................................................................................................................................. 52
3.3.1 CALIBRATION PROCEDURE.......................................................................................................................................... 52
3.3.2 LINEARIZATION POINTS ................................................................................................................................................ 54
3.3.3 ZONE OF USE DIFFERENT THAN THE ZONE OF CALIBRATION .............................................................................. 55
3.3.4 QUICK ZERO CALIBRATION .......................................................................................................................................... 55
3.3.5 CELL EQUALISATION PROCEDURE ............................................................................................................................. 56
3.3.6 ADJUSTMENT OF EQUALIZATION COEFFICIENT ....................................................................................................... 56
3.3.7 SETTING THE COMMUNICATION WITH DIGITAL CELLS ............................................................................................ 57
3.3.8 THEORETICAL CALIBRATION ....................................................................................................................................... 58
3.4 REMOTE SCALE CONFIGURATION ................................................................................................................................. 59
4. DISPLAY OF THE SCALE GRAVITY ACCELERATION AND CORRECTION OF THE WEIGHING ERROR DUE TO THE
DIFFERENT GRAVITY ATTRACTION BETWEEN THE CALIBRATION AND UTILISATION ZONE ................................................... 60
5. SERIAL OUTPUTS ............................................................................................................................................................................. 61
5.1 RS 485 CONNECTION ................................................................................................................................................................ 62
5.2 PC CONNECTION ....................................................................................................................................................................... 64
5.3 PRINTER CONNECTION ............................................................................................................................................................ 64
5.4 TRANSMISSION PROTOCOLS .................................................................................................................................................. 65
5.5 TRANSMISSION MODES ........................................................................................................................................................... 67
5.6 SERIAL COMMANDS FORMAT .................................................................................................................................................. 68
5.7 ADVANCED COMMANDS........................................................................................................................................................... 73
5.8 ALIBI MEMORY ........................................................................................................................................................................... 80
5.9 CUSTOMISATION OF THE STRING .......................................................................................................................................... 82
6. NETWORK MANAGEMENT ............................................................................................................................................................... 83
6.1 INSTRUMENT NETWORK CONFIGURATION ........................................................................................................................... 83
6.2 NETWORK FUNCTIONS............................................................................................................................................................. 84
7. SELF-SERVICE ................................................................................................................................................................................. 85
7.1 CONFIGURATION ....................................................................................................................................................................... 85
7.2 BADGE READER ....................................................................................................................................................................... 87
7.3 COIN BOX ................................................................................................................................................................................... 89
7.4 RFID READER ............................................................................................................................................................................ 91
8. ANALOGUE OUTPUT (OPTIONAL) .................................................................................................................................................. 97
8.1 OPERATING MODES ................................................................................................................................................................. 97
8.1.1 OUTPUT ON THE GROSS WEIGHT ............................................................................................................................... 97
8.1.2 OUTPUT ON THE NET WEIGHT ..................................................................................................................................... 98
8.2 CONFIGURATION ....................................................................................................................................................................... 99
9. PROGRAMMING THE PRINTOUTS ................................................................................................................................................ 100
9.1 PROGRAMMING EXAMPLE ..................................................................................................................................................... 102
9.2 ASCII CODE TABLES ............................................................................................................................................................... 103
9.2.1 CODE PAGE 1252 WINDOWS LATIN 1 ........................................................................................................................ 103
To Next Page
Loading...
Need help?
General
