PROGRAMMING P SERIES
Page 15 of 100
* "CON" - MACHINE CONFIGURATION
This function allows the user to access and change the programming of the following machine configuration
settings. If you press select button 4 and the display shows "LOC", this means configuration setting changes
will not be allowed. If "C1" is displayed, then configuration setting changes will be allowed. "LOC" can only
be enabled or disabled through DEX programming. If "C1" is displayed, the listed settings are available.
Note: You must press select button 4 with the configuration code displayed if you wish to enter the edit
mode. The “0” or “1” will be flashing to acknowledge you are in the edit mode.
IMPORTANT: All machine configuration codes are disabled coming from the factory (C #0).
C1 - Configuration Switch 1 - Multi-Price Setting Mode
This code is used to enable the single price mode "C1 O" or multi-price mode "C1 1".
Press select button 4 and “C1 #” will be displayed, with the “#” flashing.
Press select buttons 2 or 3 to scroll between "C1 O" and "C1 1".
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C1 #"and keep the original setting.
Press select button 2 to scroll to "C2 #".
C2 - Configuration Switch 2 - Optional Features Enable
This code is used to allow (C2 1) the following optional features to be displayed and enabled:
“DISC”, “OVER”, “BLC1”, “BLC2”, and “SDEP”.
Press select button 4 and “C2 #” will be displayed with the # flashing.
Press select buttons 2 or 3 to scroll between “C2 0” and “C2 1”.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C2 #" and keep the original setting.
Press select button 2 to scroll to “C3”.
C3 - Configuration Switch 3 - POS Message
This code is used to disable the point of sale message. C3 0 = enabled, C3 1 = disabled.
Press select button 4 and “C3 #” will be displayed, with the “#” flashing.
Press select buttons 2 or 3 to scroll between "C3 0" and "C3 1".
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C3 #" and keep the original setting.
Press select button 2 to scroll to "C4".
C4 - Configuration Switch 4 - Automatic Viewing of Historical Sales and Cash Accounting, EROR or
NONE
This code is used to enable viewing of historical sales and cash, and EROR or NONE automatically
when the door is opened. To enable automatic viewing option enter "C4 1"; to disable enter "C4 0".
At "C4 0" any existing errors or “NONE” is automatically displays when the door is open.
Press select button 4 and “C4 #” will be displayed, with the “#” flashing.
Press select button 2 or 3 to scroll between "C4 0" and "C4 1".
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C4 #" and keep the original setting.
Press select button 2 to scroll to "C5".
C5 - Configuration Switch 5 - Door Switch Reset Status
This code is used to reset all resettable data when the door switch is cycled and at least one data
register is read via the display when set at "C5 1" or to reset all resettable data only when the
"RESET" command is received via handheld or portable computer when set at "C5 0".
Press select button 4 and “C5 #” will be displayed, with the “#” flashing.
Press select buttons 2 or 3 to scroll between "C5 0" and "C5 1".
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C5 #" and keep the original setting.
Press select button 2 to scroll to "C6".
To Next Page
Loading...