PROGRAMMING P SERIES
Page 16 of 100
C6 - Configuration Switch 6 - Reserved
This code is reserved for future use.
Press select button 2 to scroll to "C7".
C7 - Configuration Switch 7 - Save Credit
This code is used to determine how long a credit will be saved.
C7 0 will save the credit for five minutes. C7 1 will save the credit indefinitely.
Press select button 4 and “C7 #” will be displayed, with the “#” flashing.
Press select button 2 or 3 to scroll between C7 0 and C7 1.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C7 #" and keep the original setting.
Press select button 2 to scroll to "C8".
C8 - Configuration Switch 8 - Force Vend
This code is used to determine escrow to select or escrow to price.
C8 0 will set vender to escrow to select and C8 1 will set vender to escrow to price.
Press select button 4 and “C8 #” will be displayed, with the “#” flashing.
Press select button 2 or 3 to scroll between C8 0 and C8 1.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C8 #" and keep the original setting.
Press select button 2 to scroll to "C9".
C9 - Configuration Switch 9 - Multi Vend
This code is used to allow multiple vends without re-depositing funds.
C9 0 will not allow multiple vends and C9 1 will allow multiple vends.
Press select button 4 and “C9 #” will be displayed, with the “#” flashing.
Press select button 2 or 3 to scroll between C9 0 and C9 1.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C9 #" and keep the original setting.
Press select button 2 to scroll to "C10".
C10 - Configuration Switch 10 - Bill Escrow Inhibit
This code is used to allow last bill that meets or exceeds maximum vend price to be held in escrow.
C10 0 will escrow bill and C10 1 will not escrow bill.
Press select button 4 and “C10 #” will be displayed, with the “#” flashing.
Press select button 2 or 3 to scroll between C10 0 and C10 1.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C10 #" and keep the original setting.
Press select button 2 to scroll to the next configuration code.
Press select button 1 to return to "CON".
Press select button 2 will scroll to next routine.
*"CCOC" - CORRECT CHANGE ONLY CONTROL ROUTINE
This function is used to allow consumer overpay, set a correct change value, and set an unconditional
acceptance value.
Press select button 4 will display "CON#" where # is the current setting of allow consumer overpay. Press
select button 2 or 3 to scroll to "CCU" or “ACC”.
"CON#" - Allow Consumer Overpay
This function allows the vender to vend with the risk of not being able to return the full amount of
change. This function has to be turned on”CON1” to use the value set in “ACC”.
Press select button 4 and display will show “CON#” with the # flashing.
CON1 will allow consumer overpay (customer could potentially be shortchanged) and CON0 will
not allow consumer overpay (will not allow customer to be shortchanged).
Press select button 2 or 3 to scroll between CON0 and CON1.
Press select button 4 with the display flashing the setting you wish to use to select that setting, or
press select button 1 to return to "C10 #"and keep the original setting.
Press select button 2 to scroll to "CCU".
To Next Page
Loading...