Dremel 3D40 FLEX User Manual (English)

Other manuals for Dremel 3D40 FLEX

Questions and Answers:

S
Suzanne GilbertAug 18, 2025
What to do if Dremel 3D Printers PLA is not extruding or sticking to the build tape properly?
- S
  stantonanthonyAug 19, 2025
  If the PLA isn't extruding or sticking properly to the build tape of your Dremel 3D Printer, it might be because the build plate isn't leveled with the extruder head. To fix this, cancel your current print, clear the build plate, level the build plate, and then restart the print. Leveling the build plate aligns the extruder head and should ensure better object quality.
F
Faith LopezAug 21, 2025
Why is there a spaghetti mess at the end of my Dremel 3D40 FLEX 3D Printers build?
- N
  newtonjonathanAug 21, 2025
  A 'spaghetti mess' at the end of a Dremel 3D Printer build typically occurs because: * A layer of your object didn't stick properly. * The model was saved with minimal surface area contacting the build plate. * The object was built floating above the build plate without supports. To prevent this, use the preview feature in Dremel Digilab 3D Slicer to check the first layer height and position. Always build with supports when necessary.
M
mleonardAug 23, 2025
Why Dremel 3D40 3D Printers extruder head building off center?
- K
  Kristin RobinsonAug 23, 2025
  If the extruder head on your Dremel 3D40 3D Printer is building off-center, it means the printer has lost track of the extruder head’s exact location. Sending the extruder head to the home position will recalibrate the printer. Cancel your object, clear the build plate, send the extruder head to the home position, and then restart the object.
J
Justin CarterAug 26, 2025
Why are there stringy or fraying plastic layers on steep overhangs with Dremel 3D40 FLEX?
- R
  Robert MillsAug 26, 2025
  Stringy or fraying plastic layers on steep overhangs in Dremel 3D Prints often occur because object overhangs are too far apart or too steep (less than a 45-degree angle). Build with supports to resolve this issue.
M
Matthew WebbAug 27, 2025
What to do if my Dremel 3D40 FLEX 3D Printers build did not start when sent over network?
- G
  gcooperAug 27, 2025
  If your Dremel 3D Printer build didn't start when sent over the network, here are a few possible reasons: * The filament might have run out. Load additional filament and resume the build. * The doors might be open. Ensure the doors are closed to start builds over your network, then start the build from the print queue. * A model might have been already building. The build plate must be clear; clear the build plate and start the build from the print queue.
S
Samuel HamiltonAug 30, 2025
Why Dremel 3D40 3D Printers will not connect to my network?
- G
  gatkinsonAug 30, 2025
  If your Dremel 3D40 3D Printer isn't connecting to your network, it could be due to a couple of reasons: * The printer might be too far from the wireless router. Try repositioning the 3D40 to be closer to your router. * The network password might be incorrect. Re-enter your password or verify it with your network owner.
A
Amber MaysSep 1, 2025
Why Dremel 3D40 3D Printers will not find my Wi-Fi network?
- Y
  Yvette VillaSep 2, 2025
  If your Dremel 3D40 3D Printer isn't finding your Wi-Fi network, it's likely that the printer is too far from the wireless router. Try repositioning the 3D40 to be closer to your router or connect to the network with Ethernet.
C
Caleb RuizSep 3, 2025
What to do if Dremel 3D40 3D Printers will not retrieve a token?
- C
  cynthia99Sep 4, 2025
  If your Dremel 3D40 3D Printer won't retrieve a token, it might be caused by: * An incorrect network password. Try re-entering your password or verifying it with your network owner. * The network having a firewall. Try entering network proxy information.