3D40 FLEX may become damaged. Dremel
3D40 FLEX is intended to operate in temperature
between 16-29° C (60 - 85° F).
p. Do not move or bump Dremel 3D40 FLEX or the
extruder during operation. The object may build
incorrectly.
q.
Changing the lament during building will
cancel the object and may damage the extruder.
r.
Doing so may damage the
extruder.
Dremel 3D40 FLEX will not
work properly with damaged extruder tip and will
require replacement.
t.
tape. Use of improper build tape may result in
equipment damage and poor object build quality.
u.
platform. Sudden tool slip and improper body
position during object removal from the build
platform may result in personal injury.
v.
Scratches in the build platform
will result in improper object creation.
w. Do not drop the build platform. Tempered glass
plate may break and result in personal injury.
x.
Contact with tempered glass plate
edge may result in personal injury.
y.
Tempered glass plate may
separate from plastic holder and result in personal
injury.
z.
FLEX. Structural models created by inexperienced
designers may result in property damage and
personal injury.
SERVICE
a.
Failure to do so may result in
personal injury and equipment damage.
b.
This will ensure that
proper operation and safety of Dremel 3D40 FLEX
is maintained.
c.
Use of object materials, or 3D
objects other than Dremel
®
approved object
materials and genuine Dremel
®
components may
void warranty.
d. Damage
to the product resulting from use of lament other
than Dremel approved lament is not covered
under warranty.
TABLE OF CONTENTS
......................................2
...................................................3
........................................................ 4
FCC COMPLIANCE ..............................................4
Information on Intellectual Property ...................4
........ 4
..........................................
.................................................
Getting to know your 3D40 FLEX........................
Introduction ............................................................9
..........................................................9
Touch Screen .......................................................
............................................
Initial Setup ..........................................................
Getting Ready to Build .......................................
..........................................................20
Building ................................................................23
........................................
.....................................................
Maintenance .........................................................
Maintenance and Service ...................................29
Open Source Software .......................................30
Dremel
®
................
Use of Dremel 3D40
FLEX when damaged may result in poor quality of
object creation, further equipment damage, property
damage or personal injury.
b. Do not touch the extruder tip during Dremel
Contact with the
extruder tip during or after operation before tip has
cooled may result in personal injury.
c. Set up the Dremel 3D40 FLEX in a well-
FLEX. Dremel 3D40 FLEX melts plastic during
building. Plastic odours emitted during Dremel
3D40 FLEX operation may irritate eyes and
airways. Locating Dremel 3D40 FLEX close to
surrounding objects prevents proper ventilation.
d.
Contact with Dremel 3D40
FLEX moving parts during operation may result in
poor build quality, equipment damage or personal
injury.
e.
3D40 FLEX during operation. Use of Dremel
3D40 FLEX by persons unfamiliar with these
warnings an instructions may result equipment or
property damage and personal injury.
f. Use of lament
not authorized by Dremel may result in equipment
and property damage.
g.
Small objects are potential choking hazards for
young children.
h.
i.
Plastic may melt when
exposed to re or other heat sources. Such use of
objects created by Dremel 3D40 FLEX may result
in re, property damage and personal injury.
Such use of objects created
by Dremel 3D40 FLEX may result in illness or
personal injury.
k.
PLA plastic
is not suitable for electrical applications. Such use
of objects created by Dremel 3D40 FLEX may
result in property damage and personal injury.
l.
mouth. PLA plastic is not suitable for food or drink
preparation and food utensils. Such use of objects
created by Dremel 3D40 FLEX may result in illness
or personal injury.
m.
PLA plastic is not
suitable for chemical storage. Such use of objects
created by Dremel 3D40 FLEX may result in
property damage and personal injury.
n. Do not modify Dremel 3D40 FLEX or alter
Modications may result in
equipment and property damage, and personal
injury.
o.
Dremel
3
To Next Page
Loading...
Need help?
General
