Home
DURKOPP ADLER
Sewing Machine
767
DURKOPP ADLER 767 Service Manual
5
of 1
of 1 rating
100 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
14.4
Adjust
the
thread
cutting
stitch
before
thread
cutting
St
andard
checking
The
length
of
the
last
stitch
before
thread
cutting
can
be
adjusted.
Thus,
the
lengths
of
the
cut-off
needle
and
bobbin
threads
can
be
influenced.
Both
thread
ends
should
have
almost
the
same
length.
Correction
The
length
of
the
thread
cutting
stitch
is
influenced
by
means
of
screw
1.
T
urning
the
screw
in
clockwise
direction
means
longer
stitches.
T
urning
the
screw
counter-clockwise
means
shorter
stitches.
62
1
65
67
Table of Contents
Service Instructions
1
General Safety Instructions
3
Table of Contents
5
General Notes
7
Gauge Kit
7
Position of the Lower Toothed Belt Wheel
8
Zero Position, Feed with Equipment
9
Zero Position Adjustment (Position of the Stitch Regulator Link)
9
Bottom Feed Adjustment
10
Position of the Feed-Dog in the Throat Plate Cutout
10
Height of the Feed-Dog
11
Lifting Motion of the Feed-Dog
12
Feeding Motion of the Feed-Dog
13
Synchronous Run of Needle Feed and Bottom Feed
14
Needle Bar Wing
17
Lateral Position of the Needle Bar Wing
17
Position of the Needle Bar Wing in Feed Direction
18
Hook Settings
19
Looping Stroke
19
Needle Bar Height
20
Distance between Hook and Needle
21
Hook Protection
22
Clearance in the Claw Clutch
23
Stitch Regulator Settings
24
Limitation of Maximum Stitch Length
24
Limitation of the Max. Stitch Length for Machines Equipped with 2Nd Stitch Length as Standard
25
Basic Settings of Stitch Adjustments for Machines Equipped with 2Nd Stitch Length as Standard
25
Operating the Stitch Adjustments for Machines Equipped with 2Nd Stitch Length as Standard
27
Bobbin Case Opening Settings
28
Bobbin Case Opening
28
Size of the Finger Run
28
Lifting Course
29
Timing of the Bobbin Case Opening
29
Upper Feed Settings Altering the Upper Feed
30
Altering the Upper Feed
30
Lateral Position of the Lever for Transmitting the Setting Wheel Motion
30
Setting Range of the Sewing Foot Stroke Adjustment
31
Position of the Lever for Transmitting the Setting Wheel Motion
32
Feeding Foot and Presser Foot
33
Feeding Foot and Presser Foot Stroke
33
Lifting Motion of the Feeding Foot
34
Potentiometer for Automatic Speed Limitation
35
Electropneumatic Sewing Foot Lift
38
Sewing Foot Locking
41
Lift Limitation
42
Thread Tension Opening
43
Thread Tension Lift
44
Safety Clutch
45
Engage Disengaged Safety Clutch
45
Adjust Transmittable Torque
46
Bobbin Winder
47
Lubrication
48
General Hints Concerning the Oil Lubrication
50
Hook Lubrication
51
Change Oil
52
Oil Level in the Fluid Reservoir
53
Mounting of the Head Cover
55
Thread Trimmer (Class 767-FA
56
Function Sequence
56
Thread Pulling Knife
57
Counter Knife and Underthread Clamp
58
Guide Curve, Slewing Range of the Thread Pulling Knife and Roller Lever
59
Short Thread Trimmer (KFA-373)
60
Parameter Settings
60
Mechanical Setting of the Short Thread Trimmer
60
Short Thread Trimmer for Oversized Hook
63
Adjust the Thread Cutting Stitch before Thread Cutting
66
Thread Clamp (Thread Feeding Device)
67
Errors, Cause and Remedy
67
Short Thread Trimmer (KFA-573)
68
Parameter Settings
68
Mechanical Adjustment of the Short Thread Trimmer
68
Setting the Thread Trimming Stitch for the Short Thread Trimmer
73
Thread Clamp (Thread Pulling Device)
74
Possible Faults, Cause and Remedy for the Short Thread Trimmer
74
Synchronizer
75
Controls and Control Panel Efka
76
Positioning
76
Setting the Parameters Values with the V810 Control Panel
79
Master Reset
81
Automatic Speed Adaptation
82
General
82
Setting the "Speedomat" Function
83
Optional Equipment
85
RAP 13-2 Electro-Pneumatic Seam Bartacking
85
RAP 13-4 Electro-Pneumatic Seam Bartacking
85
NP 13-4 Electro-Pneumatic Needle Return Device
86
HP 13-7 Electro-Pneumatic Quick Stroke Adjustment (Speedomat)
87
RFW 13-3 Remaining Thread Monitor
88
RFW 13-8 Remaining Thread Monitor
88
RFW 13-9 Remaining Thread Monitor
88
RFW 13-6 Remaining Thread Monitor
88
Connecting the Controls and the Solenoid Valve for the Remaining Thread Monitor
89
STLS 13-2 2Nd Stitch Length
90
VA Vertical Cutter
92
AE Edge Cutter and Binder
95
Seam Center Guide
97
FS 13-1 Additional Tension
97
NK 13-1 Needle Cooling
97
LR 13-4 Light Barrier
97
SP 470 Roller Feed Device
98
WTA 13-2 Automatic Lowering
98
Skip Stitch Detection FSE
98
Maintenance
99
Other manuals for DURKOPP ADLER 767
Instruction Manual
46 pages
Operating Instructions
46 pages
Spare Parts
87 pages
Installation Instructions
16 pages
Instructions
16 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the DURKOPP ADLER 767 and is the answer not in the manual?
Ask a question
DURKOPP ADLER 767 Specifications
General
Brand
DURKOPP ADLER
Model
767
Category
Sewing Machine
Language
English
Related product manuals
DURKOPP ADLER 768
28 pages
DURKOPP ADLER 755 A
498 pages
DURKOPP ADLER 756 A
498 pages
DURKOPP ADLER 745-34-2
94 pages
DURKOPP ADLER 745-35-10 A
284 pages
DURKOPP ADLER 745-34 Speedpocket
84 pages
DURKOPP ADLER 238
38 pages
DURKOPP ADLER 367
39 pages
DURKOPP ADLER 867
164 pages
DURKOPP ADLER 697
47 pages
DURKOPP ADLER 869-M Premium
180 pages
DURKOPP ADLER 867-M Premium
98 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
