Home
DURKOPP ADLER
Sewing Machine
887
DURKOPP ADLER 887 Service Instructions
4
of 1
of 1 rating
50 pages
Give review
Manual
Specs
To Previous Page
To Previous Page
Loading...
DÜRKOPP ADLER AG
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone +49 (0) 521 925 00
E-Mail: service@duerkopp-adler.com
www.duerkopp-adler.com
Subject to design changes - Part of the machines
shown with additional equipment -
Printed in Germany
©
Dürkopp Adler AG -
Service
Instru
ctions -
0791
887651
- 02.0 - 09/2015
49
Table of Contents
Default Chapter
5
Table of Contents
5
1 General
7
1.1 Setting Gauges
7
Adjusting the Handwheel
8
Sewing Machine with Minimotor
8
Sewing Machine with Direct Drive
9
2 Bottom Feed
10
Basic Setting for Stitch Adjustment and Stitch Length Limit
10
Stitch Uniformity for Forwards and Reverse Stitching
11
Adjusting of Feed Shaft Position and Clutch Lever Position
12
Position of the Eccentric Tappet for the Feed Movement
13
Switching over the Feed Clutch
14
Position of the Eccentric Tappet for the Switch over of the Feed Clutch
15
Checking the Switch over of the Feed Clutch
16
Adjusting the Reduced Stitch Length
17
Throat Plate
18
2.10 Slide Wheel Feeder
19
Adjusting the Wheel Feeder Height for Single Needle Sewing Machines
19
Adjusting the Wheel Feeder Height for Double Needle Sewing Machines and Sewing Machines with Edge Trimmer
20
3 Top Feed
21
Position of the Needle Holder with Single Needle Sewing Machines
21
Needle Feed
22
Roller Foot
24
Roller Foot Lifting
25
Fabric Holder for Double Needle Sewing Machines
26
4 Adjusting the Needle Bar and the Hook
27
Needle Bar Height, Play of Needle to Hook Tip, Loop Stroke
27
Hook Tip Guard
28
Bobbin Housing Release
29
Hook Lubrication
30
5 Thread Setting
31
Thread Regulator, Check Spring, Bolt for the Thread Lever Mechanism
31
Bobbin Winder
32
6 Thread Cutter General
33
Position of the Thread-Pulling Knife, Position of the Counter Knife
33
Starting Position for the Thread Pulling Knife
34
Control Cam
35
Bobbin Thread Clamp
36
Position of the Throat Plate Insert
37
7 Sewn Material Edge Trimmer Control Switching On/Off Edge Trimmer
38
Upper Knife Height Adjustment
39
Height Adjustment of Cutting Knife
40
Setting of Side (Lateral) Position of Knife
42
Setting of Upper Knife Angle with Regard to Bottom Cutting Edge
43
Material Guide Adjustment
44
Replacing the Lower Knife
45
Sharpening the Upper Knife
46
8 Electronic Control and Sewing Machine Drive - Positioning Motor
47
Terminals to PCB Connections - Electromagnetic Variant
48
Terminals to PCB Connections - Pneumatic Variant
49
Other manuals for DURKOPP ADLER 887
Instruction Manual
61 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the DURKOPP ADLER 887 and is the answer not in the manual?
Ask a question
DURKOPP ADLER 887 Specifications
General
Brand
DURKOPP ADLER
Model
887
Category
Sewing Machine
Language
English
Related product manuals
DURKOPP ADLER 867
164 pages
DURKOPP ADLER 806
53 pages
DURKOPP ADLER 827
80 pages
DURKOPP ADLER 8967
32 pages
DURKOPP ADLER 867-M Premium
98 pages
DURKOPP ADLER 869-M Premium
180 pages
DURKOPP ADLER 878-M PREMIUM
102 pages
DURKOPP ADLER 767
100 pages
DURKOPP ADLER 559
70 pages
DURKOPP ADLER 367
39 pages
DURKOPP ADLER 219
116 pages
DURKOPP ADLER 745-34-2
94 pages
To Previous PageTo Previous Page
Loading...
Need help?
General
