Eagle 200-DC - P;O Adjust Switches #1 - #4; Power ON;OFF Switch and 5-Pin Primary Plug for Diamond DC Board; Battery Replacement When Necessary

21
Battery Replacement When Necessary
Power ON/OFF Switch and 5-Pin Primary Plug for Diamond DC Board
Power Indicator LEDs
Normal battery deterioration will take place over time and batteries will need to be replaced eventually. Remove the 5-Pin Primary Connector
(White Plug) from Diamond DC Board BEFORE replacing the Eagle Battery Pack.
IMPORTANT: Use onl
y
Ea
g
le Batter
y
Pack in
y
our Ea
g
le
g
ate o
p
erator.
P/O Adjust Switches #1 - #4
Not used, leave in OFF position.
When ON, Indicates AC input power is connected to
operator and functioning normally.
When ON, Indicates battery pack is connected to operator
and functioning normally.
When ON, Indicates battery charging is taking place.
Power Switch: Connects and
disconnects the AC input power
ONLY.
IMPORTANT: Power switch does
NOT disconnect battery power to
the operator.
5-Pin Primary Plug:
Connects and disconnects
ALL power to the operator
(AC AND Battery Power).
IMPORTANT: Batteries will
NOT charge unless plug is
connected into Diamond
DC board.
5-Pin Primary Connector
When ON, Indicates low battery power. Charging will
automatically start when operator is able.
–
1
2
3
+
OFF
OFF
OFF
1
ON
2 3 4
P/O ADJUST
AC POWER
24VAC
SOLAR
POWER
LOW
BATTERY
CHARGER
ON
MH4
DIAMOND
DC
M/S PHASE
01
MASTER
OPEN RIGHT
BRAKE ON
REVERSE LOOP NC
ONE PASS ON
STOP-REVERSE ON
ALARM-RESET ON
CLOSE TIMER ON
OFF—ON
1
ON
2 3 4 5 6 7 8
SELECT
ACTIVE
OVERLOAD
OPENING
LIGHT HEAVY
ERD STATUS
GATE STATUSTIMER
MIN
MAX
CLOSING
OPEN
LIMIT
OPENING CLOSING CLOSE
LIMIT
CLOSE
STOP
OPEN
SLAVE MASTER
#14#13
+ MAGLOCK - (24 VDC)
#10
+ ALARM - (12 VDC)
#11
MAG LOCK
N / C N / O COM
#9
POWER
24 VDC
#12
REVERSE LOOP
#2
SHADOW LOOP
#3
EXIT OPEN
#4
KEY KEYPAD
#6
EDGE SENSOR
#8
STOP
#5
CLOSE
#7
LOOP WIRE INPUT
EXIT
OPEN
SHADOW
LOOP
REVERSE
LOOP
COMM PORT
OUTPUTSGLOBAL INPUTS
RECEIVER
RELAY
-24VDC
RELAY
24VDC
#1
REVERSE LOOP SHADOW LOOP EXIT LOOP
REVERSE SHADOW EXIT
RESET
+ –
+ –
+ –+ –
GND CLK GND CLK
AC POWER
24VAC
SOLAR
POWER
LOW
BATTERY
CHARGER
ON
FUSE MAX 20A
FUSE MAX 35A
20
FUSE MAX 20A
MOTOR
+–
BATTERY
+
24VAC
HNG –
LEFT RIGHT GND GND LEFT RIGHT
20
SOLAR
+
–
–
1
2
3
+
OFF
OFF
OFF
1
ON
2 3 4
P/O ADJUST
1
ON
2 3 4
AUTO OPEN OFF
POWER FAIL OPEN
OPEN DELAY MASTER OFF
OPEN DELAY SLAVE OFF
AUTO OPEN ON
POWER FAIL CLOSE
OPEN DELAY MASTER ON
OPEN DELAY SLAVE ON
OFF—ON
PWR FAIL OPERATION
20 Amp
MH2
MH1
MH3
OFF ON
Power Switch
AC Input Power Wire
Junction Box
SLAVE
OPEN LEFT
BRAKE OFF
REVERSE LOOP NO
ONE PASS OFF
STOP-REVERSE OFF
ALARM-RESET OFF
CLOSE TIMER OFF
Diamond DC Board ONLY
Diamond DC Board