22
Input Power Connection
Limit Switches
Green
MH4
DIAMOND
DC
M/S PHASE
01
MASTER
OPEN RIGHT
BRAKE ON
REVERSE LOOP NC
ONE PASS ON
STOP-REVERSE ON
ALARM-RESET ON
CLOSE TIMER ON
OFF—ON
SLAVE
OPEN LEFT
BRAKE OFF
REVERSE LOOP NO
ONE PASS OFF
STOP-REVERSE OFF
ALARM-RESET OFF
CLOSE TIMER OFF
1
ON
2 3 4 5 6 7 8
SELECT
ACTIVE
OVERLOAD
OPENING
LIGHT HEAVY
ERD STATUS
GATE STATUSTIMER
MIN
MAX
CLOSING
OPEN
LIMIT
OPENING CLOSING CLOSE
LIMIT
CLOSE
STOP
OPEN
SLAVE MASTER
#14#13
+ MAGLOCK
- (24 VDC)
#10
+ ALARM
- (12 VDC)
#11
MAG LOCK
N / C
N / O
COM
#9
POWER
24 VDC
#12
REVERSE
LOOP
#2
SHADOW
LOOP
#3
EXIT
OPEN
#4
KEY
KEYPAD
#6
EDGE
SENSOR
#8
STOP
#5
CLOSE
#7
LOOP WIRE INPUT
EXIT
OPEN
SHADOW
LOOP
REVERSE
LOOP
COMM PORT
OUTPUTSGLOBAL INPUTS
RECEIVER
RELAY
-24VDC
RELAY
24VDC
#1
REVERSE LOOP SHADOW LOOP EXIT LOOP
REVERSE SHADOW EXIT
RESET
+ –
+ –
+ –+ –
GND
CLK
GND
CLK
AC POWER
24VAC
SOLAR
POWER
LOW
BATTERY
CHARGER
ON
FUSE MAX 20A
FUSE MAX 35A
20
FUSE MAX 20A
MOTOR
+–
BATTERY
+
24VAC
HNG –
LEFT RIGHT GND
GND LEFT RIGHT
20
SOLAR
+–
–
1
2
3
+
OFF
OFF
OFF
1
ON
2 3 4
P/O ADJUST
1
ON
2 3 4
AUTO OPEN OFF
POWER FAIL OPEN
OPEN DELAY MASTER OFF
OPEN DELAY SLAVE OFF
AUTO OPEN ON
POWER FAIL CLOSE
OPEN DELAY MASTER ON
OPEN DELAY SLAVE ON
OFF—ON
PWR FAIL OPERATION
20 Amp
MH2
MH1
MH3
MASTER
OPEN RIGHT
BRAKE ON
REVERSE LOOP NC
ONE PASS ON
STOP-REVERSE ON
ALARM-RESET ON
CLOSE TIMER ON
OFF—ON
SLAVE
OPEN LEFT
BRAKE OFF
REVERSE LOOP NO
ONE PASS OFF
STOP-REVERSE OFF
ALARM-RESET OFF
CLOSE TIMER OFF
1
ON
2 3 4 5 6 7 8
SELECT
Diamond DC Board 120/240 VAC Input Power Connection
Setting the Limit Switches
120 VAC
WARNING: Eagle Access Control Systems, Inc. is not responsible for researching and complying
with local building codes. Be sure to check all local building codes before installation.
Be sure that the circuit breaker for the line input power is turned OFF before connecting the
input power to the operator.
All operators MUST be properly grounded. Installing surge protection is recommended.
The limit switches MUST be set so the gate stops at the correct open and close positions.
the control board MUST have power for the limit LEDs when setting the limit switches.
Adjust the close limit switch FIRST when the gate is in the closed position.
Open and Close
Limit LEDs will light
up on control board
for top or bottom
limit switches as
indicated.
Indicates the
direction the
gate is cycling.
IMPORTANT: DO NOT cycle the
operator before setting the limit
switches. Damage or injury could
occur if limit switches are NOT set.
(See below)
Top Limit Switch
Top Limit
Switch
Bottom Limit
Switch
OPEN LEFT OPEN RIGHT
Bottom Limit Switch
3-button
station
cycles
operator.
120 VAC Input
Power Wire
Black wire to Black wire.
White wire to White wire.
Green wire to Green wire.
Operator Wire Color Description
25 ft
14 AWG
50 ft
12 AWG
100 ft
8 AWG
200 ft
6 AWG
Single Operator 120 VAC Input Wire
Guidelines
CAUTION
To Set the Limit
Switches:
Loosen set screw and
rotate top and bottom
limit switch activators
accordingly.
Set Screw
Feature Selector #2
GATE STATUS
OPEN
LIMIT
OPENING CLOSING CLOSE
LIMIT
Indicates the
direction the
gate is cycling.
Bottom Limit
Switch
Top Limit
Switch
GATE STATUS
OPEN
LIMIT
OPENING CLOSING CLOSE
LIMIT
MASTER/SLAVE LINE INPUT POWER
NOTE: The VAC input power for the
master and slave operators MUST be on
the same circuit breaker.
Top Limit Switch Activator
Bottom Limit Switch Activator
OFF ON
Power Switch
Junction
Box
120 VAC power
outlet provided.
Junction Box
Black
Black
Green
Terminated Wire
240 VAC - Single Phase
Only use 2 wires of the
3 phase input power wire.
Terminate 3rd wire
(Do not use).
Operator Wire Color Description
50 ft
14 AWG
100 ft
12 AWG
150 ft
10 AWG
200 ft
8 AWG
Single Operator 240 VAC Input Wire
Guidelines
Junction Box
White
240 VAC
Three Phase
Input Power Wire
Black - 120 VAC (Hot)
White - Neutral
Green - Ground
(from an approved grounding method)
Black - 120 VAC (Hot)
Gray - 120 VAC (Hot)
Green - Ground
(from an approved grounding method)
Gray
Diamond DC Board ONLY
To Next Page
Loading...
