IL17569
Page 2-4
Effective June, 2001
Just press Enter, as the password is defaulted to 0, the unchanged state.
If a password has been previously programmed, use the
and pushbuttons to select which of the 4 password
characters to change, the and pushbuttons to change to
the appropriate character in each location, and the
pushbutton to enter the specified password.
2.5 Introduction to Programming
The FP-5000 can be programmed using an HMI with PowerPort™
software through the RS-232 serial port or remotely via the rear
INCOM PN using PowerNet. In addition, the FP-5000 may be
programmed directly from the front panel. We will focus on direct
programming from the front panel in this Quick Start Section.
Programming is restricted to authorized users through password
protection and through the physical restraint of a security door
which may be sealed with a lead seal.
CAUTION
CHANGING THE SETTINGS OF THE FP-5000 WILL
SUBSTANTIALLY IMPACT SYSTEM OPERATION. ONLY
AUTHORIZED PERSONNEL WHO ALSO POSSESS THE PASS-
WORD MAY MAKE MODIFICATIONS TO THE FP-5000 SET-
TINGS.
2.5.1 Entering Set (Programming) Mode
Lift the security door cover over the Set and
Test buttons on the front panel and press the
Set pushbutton. The Set LED (at the upper right
corner of the Set pushbutton) will illuminate and
the display will change to the Password request
Window. Unauthorized programming is
prevented by password protection and by
means of the security door over the Set
pushbutton, which may be secured with the
lead seal, making apparent any programming
access. Minimal programming will be described
in this Quick Start section. Please refer to the
complete programming instructions in Setting
the FP-5000, Section 5.
2.5.2 Password
The Setting Mode from the Front Panel is password protected to
prevent access by unauthorized users. In order to program the FP-
5000, a Password must be entered in to access programming
mode. Each Password is a 4-character alphanumeric value. The
FP-5000 is shipped with the password protection effectively
disabled, set to the default of ‘0000’. Entering Program Mode (or
Test Mode) with acceptance of the default password is done by
pressing the Enter button with the 4-asterisk Password display
unchanged. Each character in the Password may be modified to
any of the characters 0-9 and A-Z within program mode.
Password Window
[****]
Single Arrow For Bit
Dual Arrow for Value
CAUTION
KEEP YOUR PASSWORD SECRET AND RECORD IT IN A SAFE
PLACE. IF THE PASSWORD IS LOST, A NEW PASSWORD MAY
BE ENTERED DURING THE FIRST 2 MINUTES AFTER CON-
TROL POWER IS APPLIED TO THE FP-5000.
2.5.3 Navigation Within Settings Mode
The FP-5000 parameters that are set are either
numeric or elements of a list.
Use the Enter pushbutton to select the settings
category and value to update. Enter also
verifies the updating of settings upon exiting Set
mode.
Use the Up and Down pushbuttons to
increment or decrement setting values one step
at a time or to step forward and backward
through a presented list of settings.
Use the Page Up and Page Down pushbuttons
to increment or decrement setting values 10
times as fast as with the Up and Down
pushbuttons, or to step forward or backward
through a list of settings a page at a time.
Use the Previous pushbutton to back out of the
settings menu. However, when the “Save
Settings Window” appears, Enter must be
pressed in order to accept and save your
setting changes. If the Previous pushbutton is
pressed, all your changes will be discarded.
Numeric ranges are looped so that going past
one end of an interval brings you to the
beginning of the other end of the range for the
setting. Similarly, lists are also looped.
Upon entry to the Set Function, the user will
view the Setting Main Screen where the
selections will be seen three at a time using the
up and down navigation pushbuttons.
Setting Main
System Config
Protection
System Alarms
Logging
Contact Input CFG
Output Config
Programmable Logic
Clock
Communications
Change Password
To Next Page
Loading...
