Eaton Cutler-Hammer FP-5000 - Table of Contents

Table of Contents-1
IL17569
Effective June, 2001
SECTION LISTING
SECTION 1 PRODUCT OVERVIEW ....................... 1-1
1.1 General Description ........................................ 1-1
1.2 Audience .......................................................... 1-1
1.3 Safety and Caution Notices/Disclaimers ....... 1-1
1.4 Referenced Documents .................................. 1-2
1.5 Commercial and Trademarks ......................... 1-2
1.6 FP-5000 Hardware Resources
and Description ............................................... 1-2
1.7 FP-5000 Features .............................................1-2
1.8 Ordering Information ...................................... 1-4
SECTION 2 QUICK START..................................... 2-1
2.1 Introduction ..................................................... 2-1
2.2 Initial Checks ................................................... 2-1
2.3 Standard Mounting ......................................... 2-1
2.4 Wiring .............................................................. 2-1
2.5 Introduction to Programming ......................... 2-4
2.6 Startup ............................................................. 2-7
SECTION 3 SPECIFICATIONS ............................... 3-1
3.1 Table of Specifications ................................... 3-1
3.2 Standards Compliance ...................................3-5
SECTION 4 FRONT PANEL OPERATION .............. 4-1
4.1 Description ....................................................... 4-1
4.2 Display ............................................................. 4-2
4.3 Pushbuttons ..................................................... 4-3
4.4 RS-232 Communications Port / Front Panel
Communication ............................................... 4-4
4.5 Battery for Trip Indication ............................... 4-5
4.6 Display Modes ................................................. 4-5
4.7 LEDs ............................................................... 4-23
SECTION 5 SETTING THE FP-5000 ....................... 5-1
5.1 Entering Set Mode .......................................... 5-1
5.2 FP-5000 Setting Flowchart.............................. 5-2
5.3 FP-5000 Setting Table .....................................5-3
5.4 Logic Input Settings ...................................... 5-31
5.5 Setting Descriptions ...................................... 5-32
5.6 Default Settings ............................................. 5-45
Section 6 Installation and Wiring ......................... 6-1
6.1 Mounting .......................................................... 6-1
6.2 IQ Panel Cutout Retrofit.................................. 6-2
6.3 Wiring – General .............................................6-3
6.4 Separated Drawout Case Views
with Internal Callouts...................................... 6-6
6.5 Drawout Alarm ................................................ 6-9
6.6 Zone Interlocking Connections ...................... 6-9
SECTION 7 STARTUP ............................................ 7-1
7.1 Power-Off Checks ............................................ 7-1
7.2 Initial Control Power-On Checks .................... 7-1
7.3 Check with FP-5000 Powered ........................ 7-2
7.4 Voltage Checks ................................................ 7-3
7.5 Draw-Out Checks ............................................. 7-3
7.6 Trip Test with Built-in Function ...................... 7-3
7.7 Checks After Closing the Breaker .................. 7-3
SECTION 8 APPLICATION AND SETTINGS .......... 8-1
8.1 Over-all Measuring Principles
of the FP-5000 .................................................. 8-1
8.2 Ct Connection Options .................................... 8-1
8.3 Overcurrent Functions –
Instantaneous and Time .................................8-2
8.4 Curve Overlapping Issues ............................... 8-7
8.5 Zone Interlocking Behavior
and Application ............................................... 8-7
8.6 Voltage Functions and Protection ................. 8-9
8.7 Wye versus Delta Voltage Transformers ...... 8-10
8.8 Frequency Protection (81) ............................ 8-10
8.9 Breaker-Oriented Functions ......................... 8-11
8.10 Setting Up Oscillographic
Data Capture ................................................ 8-12
8.11 Data Logging Functions ............................... 8-13