Eaton i-on Series - Appendix VII: Log Messages; Log Events

i-on Range
Page 155
Appendix VII: Log Messages
This Appendix gives short explanations of the messages that may be stored in the control
unit’s log.
Please note that many of the messages refer to specific equipment items by the bus and
device number. Therefore, it is not possible to show in this list the exact log message that
you may be seeing on any given installation.
The list itself is sorted alphabetically by the text of the message. In the column “Event Log
Text” you will see “==” or sometimes “#”. These characters stand in for the zone, user or
device number that the control unit has recorded for the event being logged. In the
“Description” column this is shown as “nn” or “n”. In the first seven messages listed the
characters “$m” stand in for the type of communications module fitted.
Log Events
Event Log Text
Description
$m Alarm Fail
Communicator failed to send
alarm.
$m Line Fault
Communications line failed.
$m Line Restore
Communications line restored.
$m Modem Fault
Modem failed.
$m Modem Restore
Modem restored.
$m SMS Fail
SMS call failed to get to
destination.
$m Speech Fail
Speech dialler failed to send
alarm.
24hr Z=== Alarm
24 hour alarm on zone n.
24hr Z=== Restore
24 hour alarm on zone n restored.
A/C Fail
AC mains failed and was
communicated.
A/C Fail Ptn ##
A zone assigned to partition 1 with
type "AC Fail" was triggered.
A/C Restore
AC mains was restored.
A/C Rstr Ptn ##
A zone assigned to partition 1 with
type "AC Fail" was restored.
Alarm Abort U--
Alarm aborted by user.
Alarm Conf ==ER
Alarm has been confirmed by a
missing external prox reader on
keypad nn.
Alarm Conf Websvr
An alarm was confirmed by a user
on the web browser interface
typing the password incorrectly
more than four times in a row,
Alarm Conf. ==
Confirmed alarm with tamper on
keypad.
Alarm Conf. ==
Confirmed alarm with tamper on
expander.
Alarm Confirm
Confirmed alarm.
Alarm Confirm Aux
Confirmed alarm with tamper on
AUX tamper terminals
Alarm Confirm Bell
Confirmed alarm with tamper on
bell.
Alarm Confirm RK==
Confirmed alarm with tamper on
radio keypad.
Alarm Confirm Z==
Confirmed alarm on zone.
Alarm Test Call
Periodic alarm test call made.
Alarm Test Call
Manual alarm test call made.
All Comms Pths Flt
All communications paths have a
fault.
All Comms Pths Rst
All communications path faults
restored.
Alm Conf Bus# Tamp
An alarm was confirmed by a bus
tamper.
Alm Conf Panel Jam
Alarm confirmed by panel
jamming.
Alm Conf Panel Lid
Confirmed alarm with tamper on
control unit lid.
Alm Confirm SRN==
Confirmed alarm with tamper on
radio siren n.
Alm Confirm WAM==
Confirmed alarm with tamper on
WAM n.
AS defer U-- P#
User nn defered calendar setting
on partition n.
ATE L.F. All
All lines to alarm transmission
equipment failed.
ATE L.F. Restore
Line to alarm transmission
equipment restored.
ATE L.F. Single
Alarm transmission equipment has
a single line fault.
Auto Part Set #
The system was part set by
calendar setting.
Auto Ptn # PtSet
Partition n was part set by
calendar setting.
Auto Ptn # Set
Partition n set by calendar setting.
Auto Ptn # Unset
Partition n unset by calendar
setting.
Auto System Set
The system was full set by
calendar setting.
Auto System Unset
The system was unset by calendar
setting.
Autoset defer U--
User defered calendar setting of
system.
Autoset Fail
Calendar setting of system failed.
Autoset Fail P#
Calendar setting of partition failed.
Aux Tamper
Aux Tamper terminals on main
pcb open circuit (i-on160 only)
Aux Tamper Rstr
Aus Tamper terminals on main
pcb closed circuit (i-on160 only)
Aux. 14V4 Fail
Control unit 14.4V supply failed
(EUR versions only)
Aux. 14V4 Restore
Control unit 14.4V supply restored
(EUR versions only)
Auxiliary 12V Fail
Control unit 12V Aux DC not
working.
Auxiliary 12V Rstr
Control unit 12V Aux DC restored.
Bad checksum
There is an error on loading the
control unit with its software.
Batt = Fault Rst
Control unit battery restored.
Batt = Load Fail
Control unit battery failed load test.
Batt = Low/Missing
Control unit battery missing or low.
Batt Fault Restore
Control unit battery restored.
Batt= Charger Fail
Control unit battery charger failed.