Eaton Power Xpert 9395 - Page 21

Eaton Power Xpert 9395 UPS Installation and Operation Manual 164201725—Rev 15 xxi
LLiisstt ooff TTaabblleess
Table 1. Storage Area Contaminants 725 ....................................................................................................... 16
Table 2. UPS Cabinet Maximum Weights....................................................................................................... 17
Table 3. UPS Cabinet Clearances ................................................................................................................. 17
Table 4. Air Conditioning or Ventilation Requirements During Full Load Operation................................................... 18
Table 5. Input/Output Ratings and External Wiring Requirements for the Three UPM Power Xpert 9395-825/650,
9395-825/750, and 9395-825/ 825– Common Battery ............................................................................ 28
Table 6. Input/Output Ratings and External Wiring Requirements for the Three UPM Power Xpert 9395-825/650,
9395-825/750, and 9395-825/ 825 – Separate Battery............................................................................ 30
Table 7. Input/Output Ratings and External Wiring Requirements for the Two UPM Power Xpert 9395-825/450,
9395-825/500, and 9395-825/ 550– Common Battery ............................................................................ 32
Table 8. Input/Output Ratings and External Wiring Requirements for the Three UPM Power Xpert 9395-825/650,
9395-825/750, and 9395-825/ 825 – Separate Battery............................................................................ 33
Table 9. Separate Rectifier Input UPM Ratings and External Wiring Requirements for the Three UPM Power Xpert
9395-825/650, 9395-825/750, and 9395-825/825 and the Two UPM Power Xpert 9395-825/450, 9395-825/500,
9395-825/550 – Separate Battery ...................................................................................................... 35
Table 10. Neutral Bonding Jumper Wire Size (Four Wire Only - All Ratings) ............................................................. 35
Table 11. UPS Intercabinet Power Cable Terminations for the Three UPM Power Xpert 9395-825/650, 9395-825/750,
and 9395-825/825 and the Two UPM Power Xpert 9395-825/450, 9395-825/500, 9395-825/550..................... 36
Table 12. Supplied Wiring Terminal Hardware................................................................................................... 36
Table 13. UPS External Power Cable Terminations for the Three UPM Power Xpert 9395-825/650, 9395-825/750, and
9395-825/825 and the Two UPM Power Xpert 9395-825/450, 9395-825/500, 9395-825/550 .......................... 37
Table 14. Supplied External Wiring Terminal Hardware Kit ................................................................................... 37
Table 15. Recommended Installation Parts and Tools (Not Supplied by Eaton) ......................................................... 38
Table 16. Separate Rectifier Input UPM Power Cable Terminations for the Power Xpert 9395-275/225, 9395-275/275,
and 9395-250/228.......................................................................................................................... 38
Table 17. Power Cable Conduit Requirements .................................................................................................. 39
Table 18. Recommended Input Circuit Breaker Ratings ...................................................................................... 40
Table 19. Separate Rectifier Input Recommended Input Circuit Breaker Ratings ...................................................... 41
Table 20. Recommended Bypass, Output, and MOB Circuit Breaker Ratings .......................................................... 42
Table 21. Recommended DC Input Circuit Breaker Ratings – Common Battery........................................................ 42
Table 22. Recommended DC Input Circuit Breaker Ratings – Separate Battery ........................................................ 43
Table 23. TB1, TB2, and TB3 Interface Connections .......................................................................................... 83
Table 24. REPO Wire Terminations ................................................................................................................ 91
Table 25. Powerware Hot Sync CAN Bridge Card Interface Connections ................................................................ 99
Table 26. CAN Bridge Card Wiring Terminations.............................................................................................. 101
Table 27. Pull-Chain Wiring Terminations ....................................................................................................... 102
Table 28. Pull-Chain Wiring Terminations with MOBs ....................................................................................... 104
Table 29. RMP II, RIM II, or SCM II Wiring Terminations ................................................................................... 106
Table 30. J1 through J4 Interface Connectors................................................................................................. 108
Table 31. Status Indicators ......................................................................................................................... 155
Table 32. Display Function Menu Map .......................................................................................................... 158
Table 33. Display Menu Operation ............................................................................................................... 159