Emerson Micro Motion 4200 - Page 124

Emerson Micro Motion 4200

224 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

• To reset all inventories as a group:

a) Choose Device Tools > Totalizer Control > Inventories.

b) Click Reset All Inventories.

Transmitter operation Configuration and Use Manual

April 2019 MMI-20048166

124 Micro Motion 4200 Transmitters

Table of Contents

Default Chapter3
- Table of Contents3
Chapter 1 Before You Begin7
- About this Manual7
- Related Documents7
- Installation Types7
- Communication Tools and Protocols9
Chapter 2 Quick Start11
- Applying Power11
- Check Meter Status11
- Commissioning Wizards12
- Make a Startup Connection to the Transmitter12
- Set the Transmitter Clock12
- View the Licensed Features13
- Set Informational Parameters13
- Characterize the Meter (if Required)14
- Verify Mass Flow Measurement17
- Verify the Zero17
Chapter 3 Introduction to Configuration and Commissioning19
- Security and Write Protection19
- Work with Configuration Files21
Chapter 4 Configure Process Measurement23
- Configure Sensor Flow Direction Arrow23
- Configure Mass Flow Measurement24
- Configure Volume Flow Measurement for Liquid Applications28
- Configure Gas Standard Volume (GSV) Flow Measurement32
- Configure Density Measurement36
- Configure Temperature Measurement38
- Configure Pressure Measurement Unit40
- Configure Velocity Measurement Unit40
Chapter 5 Configure Process Measurement Applications43
- Set up the API Referral Application43
- Set up Concentration Measurement56
Chapter 6 Configure Advanced Options for Process Measurement69
- Detect and Report Two-Phase Flow69
- Configure Flow Rate Switch70
- Configure Events71
- Configure Totalizers and Inventories73
- Configure Logging for Totalizers and Inventories76
- Configure Process Variable Fault Action76
Chapter 7 Configure Device Options and Preferences81
- Configure the Transmitter Display81
- Configure the Transmitter's Response to Alerts85
Chapter 8 Integrate the Meter with the Control System93
- Configure the Transmitter Channels93
- Configure the Ma Outputs94
- Configure the Frequency Output102
- Configure the Discrete Output106
Chapter 9 Configure Digital Communications109
- Configure HART Communications109
Chapter 10 Complete the Configuration115
- Test or Tune the System Using Sensor Simulation115
- Enable or Disable Software Write Protection116
- MMI-20048166 April117
Chapter 11 Transmitter Operation119
- View Process and Diagnostic Variables119
- View and Acknowledge Status Alerts120
- Read Totalizer and Inventory Values122
- Start, Stop, and Reset Totalizers and Inventories122
Chapter 12 Measurement Support125
- Use Smart Meter Verification (SMV)125
- Zero the Meter132
- Set up Pressure Compensation134
- Validate the Meter139
- Perform a (Standard) D1 and D2 Density Calibration141
Chapter 13 Maintenance145
- Install a New Transmitter License145
- Reboot the Transmitter146
- Battery Replacement146
Chapter 14 Log Files, History Files, and Service Files147
- Generate History Log Files147
- Generate Service Files148
- SMV History and SMV Log149
- Totalizer History and Log150
- Generate Service Files151
Chapter 15 Troubleshooting157
- Overview157
- Status Alerts, Causes, and Recommendations157
- Transmitter Does Not Communicate174
- API Referral Problems174
- Concentration Measurement Problems175
- Density Measurement Problems176
- Discrete Output Problems178
- Flow Measurement Problems179
- Frequency Output Problems181
- Milliamp Output Problems183
- Temperature Measurement Problems186
- Check Power Supply Wiring187
- Check Sensor to Transmitter Wiring188
- Check Grounding189
- Perform Loop Tests189
- Trim Ma Output193
- Using Sensor Simulation for Troubleshooting194
- Check HART Communications194
- Check Lower Range Value and Upper Range Value195
- Check Ma Output Fault Action195
- Check the Scaling of the Frequency Output195
- Check Frequency Output Mode195
- Check Frequency Output Fault Action196
- Check the Direction Parameters196
- Check the Cutoffs196
- Check for Two-Phase Flow (Slug Flow)196
- Check for Radio Frequency Interference (RFI)197
- Check HART Burst Mode197
- Check the Drive Gain197
- Checking Process Variables198
- Check the Pickoff Voltage201
- Check for Internal Electrical Problems202
- Locate a Device Using the HART 7 Squawk Feature203
Appendix A Using the Transmitter Display205
- Components of the Transmitter Display205
- Access and Use the Display Menu206
Appendix B Using Prolink III with the Transmitter211
- Basic Information about Prolink III211
- Connect with Prolink III212
Appendix C Using a Field Communicator with the Transmitter215
- Basic Information about the Field Communicator215
- Connect with the Field Communicator215
Appendix D Channel Combinations217
- Rules for Channel Combinations217
- Valid Combinations for Channel Configuration217
Appendix E Concentration Measurement Matrices, Derived Variables, and Process Variables219
- Standard Matrices for the Concentration Measurement Application219
- Derived Variables and Calculated Process Variables220
Appendix F Environmental Compliance223
- Rohs and WEEE223

Other manuals for Emerson Micro Motion 4200

Instruction Manual40 pages

Installation Manual40 pages

Related product manuals

Emerson Micro Motion 4700

Preview: Emerson Micro Motion 800

Emerson Micro Motion 800

Emerson MICRO MOTION 1500

Preview: Emerson Micro Motion 2500

Emerson Micro Motion 2500

Preview: Emerson MICRO MOTION 2700

Emerson MICRO MOTION 2700

Preview: Emerson Micro Motion 1700

Emerson Micro Motion 1700

Preview: Emerson Micro Motion 5700

Emerson Micro Motion 5700

Preview: Emerson Micro Motion 3700

Emerson Micro Motion 3700

Preview: Emerson Micro Motion 1600

Emerson Micro Motion 1600

Emerson Micro Motion IFT9701

Preview: Emerson Micro Motion 9739 MVD

Emerson Micro Motion 9739 MVD

Preview: Emerson Micro Motion 1000 Series

Emerson Micro Motion 1000 Series