Emerson Micro Motion 4200 - Page 222

Emerson Micro Motion 4200

224 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Concentration measurement matrices, derived variables, and process variables Configuration and Use

Manual

April 2019 MMI-20048166

222 Micro Motion 4200 Transmitters

Table of Contents

Default Chapter3
- Table of Contents3
Chapter 1 Before You Begin7
- About this Manual7
- Related Documents7
- Installation Types7
- Communication Tools and Protocols9
Chapter 2 Quick Start11
- Applying Power11
- Check Meter Status11
- Commissioning Wizards12
- Make a Startup Connection to the Transmitter12
- Set the Transmitter Clock12
- View the Licensed Features13
- Set Informational Parameters13
- Characterize the Meter (if Required)14
- Verify Mass Flow Measurement17
- Verify the Zero17
Chapter 3 Introduction to Configuration and Commissioning19
- Security and Write Protection19
- Work with Configuration Files21
Chapter 4 Configure Process Measurement23
- Configure Sensor Flow Direction Arrow23
- Configure Mass Flow Measurement24
- Configure Volume Flow Measurement for Liquid Applications28
- Configure Gas Standard Volume (GSV) Flow Measurement32
- Configure Density Measurement36
- Configure Temperature Measurement38
- Configure Pressure Measurement Unit40
- Configure Velocity Measurement Unit40
Chapter 5 Configure Process Measurement Applications43
- Set up the API Referral Application43
- Set up Concentration Measurement56
Chapter 6 Configure Advanced Options for Process Measurement69
- Detect and Report Two-Phase Flow69
- Configure Flow Rate Switch70
- Configure Events71
- Configure Totalizers and Inventories73
- Configure Logging for Totalizers and Inventories76
- Configure Process Variable Fault Action76
Chapter 7 Configure Device Options and Preferences81
- Configure the Transmitter Display81
- Configure the Transmitter's Response to Alerts85
Chapter 8 Integrate the Meter with the Control System93
- Configure the Transmitter Channels93
- Configure the Ma Outputs94
- Configure the Frequency Output102
- Configure the Discrete Output106
Chapter 9 Configure Digital Communications109
- Configure HART Communications109
Chapter 10 Complete the Configuration115
- Test or Tune the System Using Sensor Simulation115
- Enable or Disable Software Write Protection116
- MMI-20048166 April117
Chapter 11 Transmitter Operation119
- View Process and Diagnostic Variables119
- View and Acknowledge Status Alerts120
- Read Totalizer and Inventory Values122
- Start, Stop, and Reset Totalizers and Inventories122
Chapter 12 Measurement Support125
- Use Smart Meter Verification (SMV)125
- Zero the Meter132
- Set up Pressure Compensation134
- Validate the Meter139
- Perform a (Standard) D1 and D2 Density Calibration141
Chapter 13 Maintenance145
- Install a New Transmitter License145
- Reboot the Transmitter146
- Battery Replacement146
Chapter 14 Log Files, History Files, and Service Files147
- Generate History Log Files147
- Generate Service Files148
- SMV History and SMV Log149
- Totalizer History and Log150
- Generate Service Files151
Chapter 15 Troubleshooting157
- Overview157
- Status Alerts, Causes, and Recommendations157
- Transmitter Does Not Communicate174
- API Referral Problems174
- Concentration Measurement Problems175
- Density Measurement Problems176
- Discrete Output Problems178
- Flow Measurement Problems179
- Frequency Output Problems181
- Milliamp Output Problems183
- Temperature Measurement Problems186
- Check Power Supply Wiring187
- Check Sensor to Transmitter Wiring188
- Check Grounding189
- Perform Loop Tests189
- Trim Ma Output193
- Using Sensor Simulation for Troubleshooting194
- Check HART Communications194
- Check Lower Range Value and Upper Range Value195
- Check Ma Output Fault Action195
- Check the Scaling of the Frequency Output195
- Check Frequency Output Mode195
- Check Frequency Output Fault Action196
- Check the Direction Parameters196
- Check the Cutoffs196
- Check for Two-Phase Flow (Slug Flow)196
- Check for Radio Frequency Interference (RFI)197
- Check HART Burst Mode197
- Check the Drive Gain197
- Checking Process Variables198
- Check the Pickoff Voltage201
- Check for Internal Electrical Problems202
- Locate a Device Using the HART 7 Squawk Feature203
Appendix A Using the Transmitter Display205
- Components of the Transmitter Display205
- Access and Use the Display Menu206
Appendix B Using Prolink III with the Transmitter211
- Basic Information about Prolink III211
- Connect with Prolink III212
Appendix C Using a Field Communicator with the Transmitter215
- Basic Information about the Field Communicator215
- Connect with the Field Communicator215
Appendix D Channel Combinations217
- Rules for Channel Combinations217
- Valid Combinations for Channel Configuration217
Appendix E Concentration Measurement Matrices, Derived Variables, and Process Variables219
- Standard Matrices for the Concentration Measurement Application219
- Derived Variables and Calculated Process Variables220
Appendix F Environmental Compliance223
- Rohs and WEEE223

Other manuals for Emerson Micro Motion 4200

Instruction Manual40 pages

Installation Manual40 pages

Related product manuals

Emerson Micro Motion 4700

Preview: Emerson Micro Motion 800

Emerson Micro Motion 800

Emerson MICRO MOTION 1500

Preview: Emerson Micro Motion 2500

Emerson Micro Motion 2500

Preview: Emerson MICRO MOTION 2700

Emerson MICRO MOTION 2700

Preview: Emerson Micro Motion 1700

Emerson Micro Motion 1700

Preview: Emerson Micro Motion 5700

Emerson Micro Motion 5700

Preview: Emerson Micro Motion 3700

Emerson Micro Motion 3700

Preview: Emerson Micro Motion 1600

Emerson Micro Motion 1600

Emerson Micro Motion IFT9701

Preview: Emerson Micro Motion 9739 MVD

Emerson Micro Motion 9739 MVD

Preview: Emerson Micro Motion 1000 Series

Emerson Micro Motion 1000 Series