Epson Stylus Photo 895 - Page 139

EPSON Stylus PHOTO 895/785EPX Revision A
Maintenance Overview 139
Table 6-2. Lubrication Point
No. Lubrication Type/Point Remarks
1
<Lubrication Point>
• The CR shaft.
Refer to Figure 6-1. "Lubrication point 1".
<Lubrication Type>
• G-56
<Lubrication Amount>
• Whole inside the CR shaft hole evenly.
25+/12.5mg x 4
• Do not attach the grease to other
portion of the CR unit.
• Use a syringe to lubricate.
• Move the CR guide left and
right, smooth out the Geese on
the surface of the CR guide
shaft.
• After lubrication, make sure that
the carriage moves smoothly.
2
<Lubrication Point>
• Contact point between PF roller and the PF
grounding spring. Refer to Figure 6-2.
"Lubrication point 2"
<Lubrication Type>
•G-26
<Lubrication Amount>
• Φ1mm x 10mm
• Do not attach the grease to the
paper path.
• Use a syringe to lubricate.
3
<Lubrication Point>
• Groove of the driven pulley holder. Refer
to Figure 6-3. "Lubrication point 3".
<Lubrication Type>
•G-26
<Lubrication Amount>
• Φ1mm x 2mm x 4points
• Use a syringe to lubricate.
4
<Lubrication Point>
• Inside the sliding slot for ASF Hopper on
the ASF Frame.Refer to Figure 6-4.
"Lubrication point 4".
<Lubrication Type>
•G-26
<Lubrication Amount>
• Φ1mm x 4points
• Use a syringe to lubricate.
• After lubrication, move the ASF
hopper manually and smooth out
the grease inside the ASF frame.
5
<Lubrication Point>
• Specified both edges area on the Front
frame. Refer to Figure 6-5. "Lubrication
point 5".
<Lubrication Type>
•G-26
<Lubrication Amount>
•
Φ
1mm x 200mm x 1 areas
• Use a syringe to lubricate.
• After lubrication, move the CR
unit left or right and smooth out
the grease on the Front frame.
6
<Lubrication Point>
• Between the Cam parts on the LD roller
shaft and the ASF Hopper. Refer to Figure
6-6. "Lubrication point 6".
<Lubrication Type>
•G-26
<Lubrication Amount>
•
Φ
1mm x 2mm
• The Cam parts on the LD roller
shaft must touch the G-26
lubricated on the ASF hopper in
the LD roller shaft rotation.
• Use a syringe to lubricate.
7
<Lubrication Point>
• Paper eject roller shaft gear, combination
gear (16.21.6) and PF roller gear. Refer to
Figure 6-7. "Lubrication point 7"
<Lubrication Type>
•G-26
<Lubrication Amount>
•
Φ
1mm x A quarter of circumference
• After lubrication, rotate the
gears manually to check the
smooth movement.
8
<Lubrication Point>
• Shaft of the ASF assembly. Refer to Figure
6-8. "Lubrication point 8".
<Lubrication Type>
•G-26
<Lubrication Amount>
•
Φ
1mm x 2mm
• Use a syringe to lubricate.
Table 6-2. Lubrication Point
No. Lubrication Type/Point Remarks